ATB1932MRS01 Amana Refrigerator - Instructions

The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harness that came with the new part. Once completed I reviewed it to make sure I didn't miss anything. I then replaced the cover over the motor area and enjoyed my success in repairing my own appliance with no added cost for labor, which would have been expensive I'm sure. The part purchased came with clear and consice instructions very easy to follow.

First I removed the two screws that secure the guard in bottom back of the freezer and removed it . Next I removed the two screws that secure the guard on the back wall of the freezer and removed it. There are three wires connected to the motor, I unplugged those and removed the two screws that secure the motor and removed it. I swapped the grommets, blade and support bracket from the old motor. I put it back together in reverse steps and its working great. My mother-in-law can,t stop thanking me ! I saved her at least $400 to buy a new fridge. Thank You, Brian Miner

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

Open the door. Removed two screws holding the cover of the thermostat. There is a clip which holds the thermostat in place. Remove the clip. Take out the thermostat. Remove the thermocouple (the long grey metal with the coil at the end) which is also held in place by a clip. Replace with the new thermostat and thermocouple and clip into place. Replace the screws to the cover. Close the door.

I was clening my uprght freezer and noticed that it was preped for an icemaker. I first went to the Whilpool website and could not find my part as my freezer was a 2008 model.

I saw PartSelect on the search page and went to thier site.
I put in my modle number of the Whilpool Ice maker kit that was on the back of my freezer. PartSelect had the part in stock and approx $18.00 less than the other kits listed on the Whilpool site (that did not match my kit number). I orderd the kit on Sunday and it arrived on Wednesday. It took less than and hour to install. Every part I needed was included. The following day I installed the water line and now I have an extra icemaker.

First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the lead wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!!

We have a side-by-side fridge/freezer and we experienced a hot center post (where doors come together) and the fridge made loud noise. Also, the (old) fan motor would start, but then quit, so our issue was the motor.

For me the repair was very easy, but for an unexperienced person it may prove to be difficult. If you must order a motor/fan, do NOT order the metal fan as a plastic fan comes with the motor. What's strange is the new motor is different than the old one, but it still mounted without any required modifications. I did NOT use the wire harness that came with the motor either as it was different too, but my old one was still good.

Check all of your parts as my fan had a cracked blade, but I used "superglue" and it's fine now.

Fridge stays cold and my wife had to lower the temperature in the fridge as she was blasted by the cold!

Glass sheet came in perfect condition, just put back in refrigerator and has been fine ever since. Not the first time I had ever taken out to clean, but it will be the last. From now on, I clean it in the refrigerator.

The procedure was straightforward. I removed the cardboard backing on the lower back of the refrigerator to expose the fan unit. I then undid the electrical harness at the fan. I then removed the three screws securing the fan motor to the metal bracket. This is the hardest part in that I had to reach through and get to the screws with my small tools. I then removed the old motor and blades and placed the new motor and blades. Again, a bit tricky trying to get the three screws mounted into the bracket...small tools and hands helps. After that I used the electrical harness supplied with the kit to plug into the new motor and I was done.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

We took the edge out of the slot and pulled the old one off then put the new one on. Once we got the plastic edge started into the slot it was a breeze. Only took about 5 minutes. We were very pleased with the results.

I unplugged the power cord. Then, I removed the housing at the inside-top of the refrigerator by removing the two screws that hold it in place. This exposed the defrost timer. I removed two clips that hold the timer in pace. Then unplugged and removed the old timer, and plugged-in and secured the new timer. Then, screwed the housing back to the top of the refrigerator. Just be careful, I partially broke the tops off the two pins that slide through the timer's body (when attempting to removed the clips that sit on the pins). Not a big deal, as the timer will remain in place without the top of the pins. Next time, I would cut the clips using diagonal cutters.

Definatly a two man job. I suggest you put a pad down to protect your floor. Remove the filter, grill, and bolts per instructions. Everything is straight forward. Move the frame back 1/2 to 1 inch then tilt the frig back on it's side about 4 inches. If the frame doesn't drop down, move it back until the front of the frame comes of the front lip of the frig. Place a block under the frig lip NOT the frame and WATCH YOUR FINGERS. The wheel should be hanging down. Just pull out the pin, replace the wheel (make sure you have it facing the correct way) and tilt back and pull the blocks. Move the frig back in place and replace the bolts. Took me and a buddy less than 30 minutes.

Very pleased with the delivery time. Was able to repair the refrigerator before the beer got hot. Replacement was easy.
Removed blower housing. Replaced motor. Put blower housing back in place.