ASD2275BRW00 Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jessica from WILLIAMSBURG, VA
- Parts Used:
- WPW10225581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Part went bad the freezer was freezing up and refrigerator not getting cold
I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from ROYSE CITY, TX
- Parts Used:
- WPW10276348
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced cracked slide out glass shelf with new one
Simply slid out damaged shelf and slid in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MESQUITE, NV
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
ice container bin cracked and had a hole in it.
Took it out of the box. Emptied the ice out of the broken bin. Slid the new one in and all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from SHERMAN, TX
- Parts Used:
- WP2309941
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shelf was broken on one side.
The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from VANCEBURG, KY
- Parts Used:
- WPW10179146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inlet valve was broken at the water line connection
Changed inlet valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Liberty hill, TX
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
Ice Bin Auger Drum was broken.
First, I removed the 6 screws which hold the ice bin to the drum and the front cover. I then removed the screw which holds the door lever and bracket to the ice bin. Then I took the C clip and washer off the end of the auger to remove it from the housing. I removed the plastic nut to remove the auger drum from the auger shaft, being careful to place the blades on the table in the order they were removed. I then installed the new auger drum on the shaft and re-assembled everything in the reverse order. This was really easy for me because I had replaced the auger previously. (about 2 years ago)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elyse from Skokie, IL
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the light socket broke apart
I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from COLUMBIA, SC
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced filter for ice maker
I removed the filter from the box I took the old filter out and inserted the new air filter put the cover down and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from ENDWELL, NY
- Parts Used:
- WPW10225581
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer Temp was -20 to -30 degrees F. and did not defrost because of the extreme low temperatures.
The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Orange, CA
- Parts Used:
- 8201515
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker in the freezer section quit making ice cubes.
First I had to figure out how to get the old unit out so I could work on it. The three screws that others wrote about were the ones that hold the motor in place. There are 3 screws holding the ice maker in the frame, along with one screw covering the electrical connection. The electrical connection was difficult to unplug because the locking tab was on the back side of the connection and with no room to work in the freezer it didn't become apparent until several frustrating minutes went by. There were no instructions provided, the picture on the ordering page showed the complete ice maker, and for $80 you get a printed circuit board with a small round item which must be the motor/timer control. The two plastic parts for moving the ice from the ice maker were included but not replaced because I didn't notice them until I had finished replacing the ice maker back in the freezer and wasn't going to start over again.
Once installed, there wasn't any noise, even of water flowing like the old one, could not tell if the unit was working or not. In the morning there was new ice in the bin indicating the repair had been successful. This is like anything else, if you have done it before it is a 5 minuter job but when you have to look at it and try to figure it out it takes a bit longer. All in all, it was simple enough, I was expecting a complete ice maker unit like was in the picture when ordered but only the motor module was actually needed.
We have another refrigerator/freezer that has an icemaker that is over 20 years old and has never been repaired, it is a Sears model though, probably made by Whirlpool or someone else.
Once installed, there wasn't any noise, even of water flowing like the old one, could not tell if the unit was working or not. In the morning there was new ice in the bin indicating the repair had been successful. This is like anything else, if you have done it before it is a 5 minuter job but when you have to look at it and try to figure it out it takes a bit longer. All in all, it was simple enough, I was expecting a complete ice maker unit like was in the picture when ordered but only the motor module was actually needed.
We have another refrigerator/freezer that has an icemaker that is over 20 years old and has never been repaired, it is a Sears model though, probably made by Whirlpool or someone else.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from SINCLAIR, ME
- Parts Used:
- 2159081
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
The door would not stay closed after it was installed. It was as if there were no magnets in the gasket.
We used the hair blow dryer to soften the gasket after being in the package. We laid it on our bed and made the gasket straight with the heat of the blow dryer. Then we began to install the gasket and once we installed it, the door would not stay closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from MORRO BAY, CA
- Parts Used:
- WP2182179
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
refrigerator door not working properly
Just as shown on your video.The refrigerator side was not sitting even, clunked and did not seal right. I decided to do.both sides, refrigerator and freezer while I was at it as our refrigerator is about 16 years old. Everything went in easily and saved us a lot of money. Very happy with the parts and repair video. Got the refrigerator nice and cleaned out while we were at it..Us and the refrigerator are breathing easier now..Yeepppeee....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from MORGAN CITY, LA
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer ice maker not dispensing ice.
Ordered Ice Bin Auger and changed with no problem. Found how to change on YouTube and followed video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from WASHINGTON, DC
- Parts Used:
- WPW10300022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ice maker leaking
Unplugged freezer turned off water removed 3 nut screws Unplugged old ice maker installed new ice maker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from OCOEE, FL
- Parts Used:
- WPW10397394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
SENT WRONG PART
ON PART DESCRIPTION EXPLODED PICTURE OF PARTS, I ORDER PART #6 (CONTROL PANEL PLASTIC FACE PLATE) AND WAS SENT PART #3 (DRAIN PLATE)
ALL I NEEDED WAS THE BLACK PLASTIC FACE PLATE.
VERY DISAPPOINTED.
ALL I NEEDED WAS THE BLACK PLASTIC FACE PLATE.
VERY DISAPPOINTED.
Was this instruction helpful to you?
Thank you for voting!