XRBS017BW0 Amana Refrigerator - Instructions

Unloaded refrigerator. Pulled refrigerator from wall. Removed bottom panel on back and replaced bolt. Reversed steps but leveled rear wheel before reloading.

Removed the lid and pantry drawer. Removed crisper drawer on right side and glass shelve. Removed 2 screws on glide. Removed 2 nuts with nut driver. Gently tugged on the pantry end cap and it released from the back wall. Had to rotate about 90 degrees to remove the extension off the back wall so I could remove the thermostat control arm from old piece and put it onto the new piece. Gently removed the thermostat control through a series of squeezing pieces and rotations. Do not force anything. Take your time as you are working with plastic that could break at any moment with force. Replace in reverse order.

Part was pretty ubiquitous so plastic door pins part fits a lot of refrigs, no tools necessary, new part is flexible enough to bend slightly to fit over pins at side. Mine was a bottom freezer type.

Actually shouldn't you have included installation instructions with the product?
I had to search for installation instructions on Utube or the job would have ended in another cracked crisper frame.

This was actually very easy, take the two crispers out and the glass panel over the large drawer and the two holding brackets that hold the glass above.

then just use a nutdriver to remove the three nuts, gently pull the piece out and remove the slider with a screwdriver (two screws). Attach the slider to the new piece reinstall, it's very easy. Took 15 minutes tops.

This was for the left side the right side might be more problematic with the additional humidity controls I don't know ....

I have to say this was the smoothest repair ever! It was easy to find on the site, ordering was easy, part came, snapped off, snapped on new drawer, FINISHED! Thank you!

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

First I removed the pantry shelf and all the shelving on the bottom half of the fridge. I used the nut driver to remove the RH pantry end cap. Very easy. I took a picture with my digital camera to make sure that I remembered how the assembly looked when puttin git back together. Very easy to do. Common sense repair.

had to remove shelving, crisper's, then unscrewed end cap. lifted it off set pin. and reversed for reinstallation. reefer door is reversed which makes it prone to close on crisper if not fully closed

With 2 babies and a chaotic household, i failed to double-check the measurements before I ordered the part. No fault of partselect, just user error ;-) I had to return the part bc i ordered the wrong size. Lesson learned, take my time and make sure it's done right the first time. The part fit in perfectly.
I used the search feature on the left side of the website to find the part, since the deli drawer wasn't in the parts diagrams given. The second time, customer service helped me find the part since the correct part wasn't on the website initially.
The deli drawer for this model is in the perfect place to have something dropped on it time and time again. I'm surprised you don't get more requests for this part to be replaced. It's bad design for Maytag to make it out of thin plastic.
Anyway, thanks so much for your patience in dealing with this frenzied mom! :-)

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.

I'd been looking a broken plastic for 3 years. Googled Partselect on a whim and one week later a new drawer and lid arrived at my door. 10 minutes later the refridgerator was like new again.

No tools needed. Snapped right into place, easy as could be.