TXI18K (P7803239W) Amana Refrigerator - Instructions

Arrived soon than expected. Unplugged some wires, removed face plate, 3 screws--install and do reverse.

Easier than I would think---Saved $150- to have someone else do it.

Works fine.

The video of the installation was the best help I have ever had. Rather that vague written instructions that are usually so poorly written they are of no help, the video showed exactly how to do it. I wish everyone provided videos like this!

Removed the elec connection (after unplugging app) found it easier to remove from appliance. Remove the three screws ( do not temove,....just loosen, the top two) bottom must be removed! Insert the power connection, exchange the tilt up rod, line up the water connection and place back on the two top screws. Tighten and relpace the bottom screw. I found out the hard way.... you cant't see the two top screws . The slots on the ice maker just fit over the screw heads.... it's cold in there!!!

Hopoe this helps..

Cape Cod

Removed old ice maker, had to use the wire shutoff from old ice maker installed new one. Very easy repair, very nice product cheapest price on internet.

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

Model#MBF2255KEW (bottom Freezer) Turn fridge and freezer controls OFF. Move fridge out away from wall to give yourself working space and to clean later. Disconnect electrical plug from wall. Turn off water supply at wall or floor. Put down towel to catch excess water and disconnect water hose at water supply, lay it on towel. Move to the inside of freezer and remove freezer bins by pulling the door all the way out as far as it will go and then lifting by the handle up. locate the two hooks in the back and push forward to clear the bar and move to a safe location. Push the two rails all the way back into the freezer. Un plug wire harness from freezer by squeezing both side of the plug at same time and pull off. Remove the 3- 1/4" nut screws (2 at top and 1 at bottom ) from the ice maker and remove. Take the front cover, Wiring harness and wire bail from old ice maker and place it on the new ice maker. Install new ice maker and connect the wiring harness plug to the freezer connection. Hook up water line hose and tighten. Turn water on and check for leaks. Plug fridge into wall outlet and set refrigerator and freezer controls to 3 until refrigerator is cold and then set as needed. Give the ice maker from 3 to 6 hours to freeze and wait for that magical sound of ice being dumped into the bin. Throw away first batch of ice to make sure there are no impurities. Check for the delivery date of the new ice maker before you start and have coolers and ice for perishables. I removed the old one on the delivery date and cleaned the fridge and freezer inside out. I came to this page to get my repair plan and I hope this will help someone else.

By replacing it with a new ine maker.

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

Like you video

Replaced Icemaker

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Remove bottom screw loosen 2 top screws unplug connector from back of icebox. Lift up and pull forward. Swap front cover full bucket stop bar and wire (plugs in) reinstall 10 minute job

the diagnosis was the most difficult step.. and trusting that the one visible nut was the only thing holding it on.. (there are 2 other clips that you need to use a little force on to detach). remove the ice maker (one nut, 2 clips, detach plug).. then remove the 3 screws holding on the 'face' , pry face off, you will see where the 'contact' has burned/melted/worn away. replace unit. 80% of the time, this is the problem (according to my research)

Five minutes with a phillips screw driver and the cube maker was changed. . . In the process, I failed to unplug the unit, and shorted the fill valve in the back. Again, five minutes with a nut driver and it was changed. No need for a PHD or the cost of a service technician for either job.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.