DRT1702BC (PDRT1702BC0) Amana Refrigerator - Instructions

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Really easy. Turned the water off, unplugged the fridge and took off a few bolts and swapped the valve out for new. It was basically plug and play. The ice maker started working its next cycle.

Used online resources to deteremine that it was either the icemaker not telling the valve to open or the valve no opening so ordered both and started with the valve (cheaper part). Turn off the water, removed the mounting screws, disconnected the plug, removed the water line (used the wet vac to suck up water while it leaked out). and disconnected the inlet line. Reconnected everything in reverse order but left unmounted until sure it worked, turned water on and waited.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

This water valve is slightly different from the original on my older GE refrigerator (i.e., the mounting bracket is larger and oriented differently, thus doesn't fit). To still use the part, I first tried mounting the new valve on my original bracket, but this resulted in a sideways mounting of the solenoid/magnet valve. This orientation generated a slower and noisier water pumping action (the solenoid/magnet valve is assisted by gravity, so it needs be installed with the top of the solenoid facing up). Then I opted to use the original valve plastic housing and bracket and switch out all rubber seals and gaskets and the enitire solenoid/magnet assembly from the new one. This worked like brand new.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Screwed in light bulb and glass protector

very easy

Turn off water supply. Unplug the refridgerator and move so easy access to back. Remember to lower front right wheel to lift rubber foot off ground. Locate valve and remove, note color orientation of wiring (I did not have to remove cardboard cover.) Have a bucket and towel handy because water will spill. Compare the valves to ensure correct part. Apply teflon tape to threads and reconnect hoses and turn on water supply to check for leaks. Then connect power supply and re-attach to refridgerator. Use vac to clean back of refridgerator of dust and build up. Move refridgerator into position and raise front right wheel until rubber foot is back on floor. Use vac to clean coils in the front of the refridgerator. Replace grill. I allowed 4 batches to run before using ice. Pretty simple repair.

Removed old water inlet valve and replaced same with the new one. Installation was easy, parts came quickly, and I now have ice cubes again. Thanks for your help.

This was an easy fix. The first thing you need to do is shut off the water to the ice maker. Then unplug refrigerator. Then take the panels off the back of the refrigerator to get to the water valve. The valve is at the bottom left hand corner. Take the inlet hose off and the outer hose off of the valve. Take the screws out to remove the valve from the panel. Replace the valve with the new one and hook up the hoses again. Make sure to tighten securely so that you do not have any leaks. Put everything back together and plug refrigerator in. Turn on water slowly and check for leaks. If no leaks, push refrigerator back and wait for the ice to begin. Piece of cake!!