ARB2117BB (PARB2117BB0) Amana Refrigerator - Instructions

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

After checking the water valves ordered new ice maker. received the part three days after ordering! Clearing out food, removing the old one and installing the new unit took under 15 minutes. Everything went fine.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.

Unplug refrigerator, remove ice maker if you have one, all you need is a 1/4 " nut driver or socket. I used a 1/4" drive socket set with a1/4" socket. After the ice maker is out of the way, remove the panel on the back of the freezer to expose the fan. Remove the 2 screws holding the fan in place , and disconnect the wires that are plugged on to the connectors. Remove any ice that has built up around the condenser and install the new fan. Plug the refrigerator back in to insure the fan runs. If it works, unplug refrigerator again and install the panel over the fan, and install the ice maker again. Plug the refrigerator back in and put all your frozen food back in the freezer. That's it , Simple!!

Replacing the icemaker is pretty simple. Three screws, an electrical connector. Hardest part is getting to the icemaker since the freezer is below the refrigerator.

installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.

I emptied the refrigerator, pulled out the crisper drawers, removed the left side crisper frame and support post, slid in the new frame and post (no tools required), reinstalled the crisper drawers, reloaded all the food back into the refrigerator. I was done in less than 15 minutes. One of the easiest repairs I have ever had to do.

remove 3 screws,rotate assembly,depress lock on wire harnass connector,un plug harnass.remove old assembly,remove and transfer side cover and steel wire at front of assembly,connect harnass to new assembly,rotate into place,aling screw holes and install 3 screws.flip front steel wire down and wait for about 1 hour,first tray of ice will fall..all done.

I had to remember how the original broken part of the drawer glide was placed in relation to the other parts of the drawer. I removed the screws for the moving parts and took the broken glide off. I crossed my fingers that the new plastic glide didn't break as there were a couple of places where the glide had to snap into place. It worked perfectly.

Very simple fix, remove 3 screws, two connectors to the old switch

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

to easy to describe, remove 3 screws and a wire plug then install new unite.
Works great
Thanks

Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.

I was heartbroken when I shattered the 27 inch long glass shelf while cleaning the refrigerator. It slipped out of the frame when I was sliding it back in. Part Select came to the rescue. Not only did they have the replacement glass for only $20, but it arrived practically the next day! I just slid the glass right in. No tools necessary.