TX18M (P7858506W) Amana Refrigerator - Instructions

The repair was straight forward and was not hard. You do almost need 3 hands as the reinstallation of the inner door panel can be awkward. The only issue that I have is that the new seal has a poor fit. While it was received folded over on itself, this was not the problem. The seal does not expand enough on one side to fully seal the door. It also has a very weak magnet. If the magnet was stronger, then maybe it would seal better. It does still leak to some extent. The seal that was removed had a stronger magnet that the new one does. I would include a photo, but this system does not allow me to add attachments. Overall, I'm pleased with the time that it took to get the gasket, and the ease of replacement, but am not satisfied with the quality of the sealing or the strength of the magnet that holds the door closed. I would rate replace as 8 out of 10, and part quality and how it works as a 2 on a scale of 10.

inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."

I have a side by side Amana fridge about 12 years old. One day I noticed everything was not cold anymore. I checked the temp with my infrared thermometer and it was about 70 in the top of the fridge, 40-50 in the bottom, and freezer was the same! So after pulling out the two baskets in the bottom of the freezer and the side rails that hold the baskets, I used a 1/4 nut driver to remove the back lower panel. After looking at the electrical schematic on the back of the fridge, I jumpered around the defrost thermostat, a little cylinder with two wires coming out of it. Bingo, the fan turned on. Well after a few days of running fine with it jumpered my new one arrived. I never really tested my old one with a meter so I did that and it tested fine, so I plugged the old one back in and it worked fine for a few days. Then one day I noticed that fan wasn't running again so I just put the new one in. I had to cut one of the connectors off as it was female instead of male and crimp cap it together, but besides that it went fine. So after connecting it I noticed the fan motor was buzzing but not spinning. I wiggled wires around and determined the connector going into the fan motor had to be a certain way to make the connection. I unplugged it, it wasn't corroded or anything but if pulled down on, it would not make connection. So pulling up on the connector proved that it would make good connection, so a ziptie keeping the wires tight in the up direction proved to be the solution. I'm pretty sure my old defrost thermostat was not the problem. So that's my story. Hope it helped.

First of all let me say I can't believe I fixed it! And I can thank this website for it, they also had my part at my front door in less than 24 hours. I am so amazed! I am a stay at home Mom, and because my husband is always off with the military I knew the job was up to me to fix. And because times are tough we certainly couldn't afford a repairman. After reading many stories here about the same problem I had, I diagnosed what was wrong with my refrigerator. The defrost thermostat was faulty. First thing to do was turn off the refrig and then unplug it. I then emptied the bottom freezer, used a screwdriver to remove back panel wall. Lo and behold the coils were covered with ice. I defrosted the freezer using a blow dryer, also had to empty the drip pan in the back. when it got full of water. ANd because there is no way to remove the drip pan, I actually got a small air hose from my son's old fish tank(clean one) and then siphoned the water into a pot, took all of 10 minutes! I then used needle nose pliers to remove the bad defrost thermostat from the refrig's wiring.The defrost thermostat which had a bulge in it so knew I was on the right path. I looked at the new defrost thermostat and they had different ends on it then the one I just removed, and I remember reading what another member did, and that was to cut off the connecting caps, strip the wires , use electrical tape to join them and use a crimping tool to place the old caps on to the new defrost thermostat .I then inserted the thermostat to the freezer's wiring. Hope that makes sense to everyone. WEll, everything is running great! Thank-You Part Select, you saved me lots of money!

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

remove ice maker vent and back piece. Unclip defrost thermostat and unplug. Plug new thermostat in and clip to element, reattach back piece, vent and ice maker. Is a tight fit getting icemaker out, there are 3 screws 2 on top and one on bottom.

Once I removed the contents of the freezer I found ice on the inside back panel Removing the panel I found ice on the cooling coils and the defrost thermostat was bulged out where the wires were attached.I removed the panel with the nutdriver as shown in the video. I removed the ice maker connection and removed the panel from the freezer section. I then had to manually defrost the area with a heat gun. The ice had actually covered the Defrost Thermostat - which was bulging where the wires were attached.. The defrosting took the majority of the repair time - the actual Defrost Thermostat replacement only took about 20 minutes once I could get to it. I spliced the wire with a crimping tool as discussed in the video. Once all was defrosted I reversed the operation.Overall, a very simple part change out. The video was extremely helpful - if nothing else to mentally prepare me for the task.

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

It made so so easy watching the video. Thank you for that. I was ready to but a new one for about $800. but I did the repairs in about 20 minutes for about $23. Thank again

The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.

unplug refrigerator,remove content [shelves] then remove panel screws,slide thermostat from tube and unplug both wire ends,match up both thermostat[old unit have male round connector] you'll need round connector.cut old unit wire off,cut new unit wire,strip both ends join with solder and cover with heat-shrink and reinstall,fridge is cooling now.

Ordered new fan motor on line took out old motor and replaced with new one

I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.

removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.