IC4N (P1110801W) Amana Refrigerator - Instructions

Piece of cake. Removed two screws, pivoted old ice make up, lifted it out of the mounts. Installing the new one was just the reverse.

Identifying the correct replacement ice make was easy also, due to the photographs on PartsSelect.com

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

very easy, 3 screws,took old one out, take 2 inter screws out (of ice maker) of old unit to replace water feed cup on new unit very easy,installed had ice after 12 hrs.

It was real easy. I unpluged the fridge. Took out the three screws that held the icemaker to the wall. Unpluged the wire harness. Removed the old icemaker and reversed the order to install the new one. Everything lined up perfectly.

Removed two screws on top. Then one under the ice maker ,held on to it while I unpluged the white flat plug. Then installed new one in reverse. Of course re-connect power wires on.
I turned power off at fuse box.
First batch of ice in an hour or so.

First i removed the top two screws that help the ice maker in place then remove the bottom screw, then unplug unit from freezer, removed ice maker for freezer, took out wire harnes, put wire harnes in new ice maker, plug new unit in place the unit in freezer and put in the bottom screw, them align the top two screw and but them in and was done. Check ice maker in two hours and there was new ice being made.

I removed the old icemaker, took it out to my shop & removed the wiring and etc. and put it back in place.

I first loosened the hex screws and lifted the unit off. Then I unplugged old unit from the wiring harness. I did have to switch the inlet funnel since the new unit was a little different. I used the one from the old unit. I then plugged it back in, rehung and tightened the screws. The unit started operating within a few hours.

First i removed the three screws that held the assembly to the fridge, then removed the water flow tube from ice maker. 2- flipped ice maker over ,then used a small flathead to push in locking tab that held wire harness and out comes ice maker. All though the water cup was not quite the same i used the old ice maker to take apart to see how it was put together,hopeing there wasn't a myriad of parts. -NO INSTRUCTIONS- piece of cake, don't take out outside screws,take out the 2 inside screws-these srcews hold the guts to the water tray-pull apart and reassemble the unit after you have switched the cups. then reinstall into fridge with your outside cover and the full bin wire and your done. It helps to be alittle mechanicly inclined. -NO GUTS NO GLORY,DONT BE AFFRAID TO LOOK OUTSIDE THE BOX-

Followed the other directions -- I have the bottom tray freezer. It was really easy to unscrew the screws -- a bit of a reach to get them all, but not a problem. Leave the top screws half-way in and it's a bit easier (the icemaker has the brackets that just sit on the screws). Thanks to everyone who left instructions!

I read the instructions from your site, removed the old unit, salvaged the parts to be reused and reassembled. 1/2 hour later I had ice and no leaks.

I took the screws out holding old old ice maker, unpluged the electrical socket and old unit came right out. All I had to do then was plug electrical socket into new icemaker place unit in position and put the one screw back in the held it in place. Plug frig and and it filled with water in about 15 minutes and started making ice. Part was a exact match to the one I removed.

Unplug fridge, close off water supply valve. Remove two screws attaching assembly to freezer wall, detach wiring harness. Remove parts from old assembly: wiring harness, shut-off rod, harness clamp and attach to new assembly. Connect wiring harness, two screws attach new assembly to freezer wall. Plug in fridge and open water supply valve (after an opportunity to change in-line filter). Works now!

First I removed the screw holding the ice maker on the wall and then loosen two other screws in oreder to remove the maker. Once out, I replaced the maker with the new one. Then replaced it in the refrig.

Most of the stories on repairing this ice maker indicated that was real easy until describing the Amana version. The fill tube attaches differently. The recommendation was to use your old "cup". I have found that to make the change required that you find a philips screw driver and locate two access holes in the motor end of the control unit. you can loosen those two screws (they won't fall out) all of the way and pull the control unit from the tray part of the ice maker. DON'T remove the three screws that hold the control unit together or rotate the sprocket. This will allow you to disassemble the parts that hold the "cup" in place. Just remember "if it isn't coming apart easily your not doing it right".