2599CIWW (P1121501W W) Amana Refrigerator - Instructions

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Used socket set to remove screws. Removed the wire harness, then removed lift arm from old ice maker and then put lift arm on the new ice maker. Reinstall wire harness then installed back in freeze with the screws. Video was very helpful. I will do business with Partselect in the future. Shipping was very fast. Thanks Partselect

I didn't. Don't know how to get to light bulb to change it for this specific model

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

The door seals arrived in good condition, I followed the instruction and unpacked the door seals and straighten them out on the floor. I left them over night to climates. First I empty all the door compartments of food. I then used socket driver and loosened all the hex nut screws around the door. Do not remove the screws. Removed the door seal by pulling it out of the door seal clamp. Once removed clean the door seal clamp and door. Now start at the top and put the door seal into the top door seal clamp. Then work on both sides of the door pushing the seal into the clamp. Finally stretch the seal and insert the bottom section into the door seal clamp. Check and make sure the seal is properly installed around the door seal clamp and the fit is even. Start at the bottom and tighten the bottom screws. Then start tightening the sides and finally the top screws. Make sure there are no wrinkles. If there is undo the screws and reposition the door seal. This is an easy install but takes about 2 hours to do.

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

Removed pin holding the wheel along with leveling screw. Put new wheel in place, replace pin and screw. Done...very easy.

Shut off the water supply at the wall then using a 1/4" nut driver I removed the steel and cardboard backing plates from the rear of the refrigerator. Disconnect the main water supply hose and then the two water lines for the chilled water dispenser and ice maker. Remove the two screws on a support bracket which holds the valve in place.
Reassembly in reverse order.
The process was very easy and took no longer than 15 minutes and works just like new. This is a good time to do some thorough cleaning around the fan and coils to keep them working properly as well.

Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.

First I turned the water off behind the refrigerator....took the ice maker inlet valve off, put on the new one. As simple as that & it is working beautifully....not only am I a woman but 55 yrs. young too!
With the right part & right tools NOTHING is impossible & I saved myself a repair persons fee!!!

Tried to repair existing valve which I have succesfully done many times by cleaning and removing grit from internal neoprene parts until new parts received. Was not successful. New valve worked perfectly. this is only 2nd repair needed on this ref. since new. 1st was defrost timer. Ice maker hasn't missed a lick since new.

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same time to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

pulled cover off back of refrigerater at the water line,shut water off removed water line,check for pressure at the line by puting the line into a 5 gallon bucket it was ok.took the dispencer lines off that goes up to dispencer,hit dispencer switch could hear buzzing at the dispencer unit but no pressure.so i replace water inlet valve

For the icemaker, I removed the ice tray and loosesned the two attaching screws(1/4"). I removed the lower bracket and then removed the ice dispenser motor cover below the ice maker. This made it easier to remove the wiring harness. After removing the icemaker from the refrigerator, I swapped out the wiring harness and ice detector bracket (wire bail that swings). Hooked things back up and went on to the water valve. All in all about 15 minutes and pretty easy.
For the ice valve, you must turn off the water supply, disconnect the power plug and move the refrigerator away from the wall. (Now's a good time to clean out under and behind the unit!) Remove the valve from the base with the 1/4" nut driver. Remove the inlet line(standard hose fitting).Have a sponge handy. Remove and replace the new valve in the bracket by popping the clip off and on the new one. Replace one outlet line and electrical connection at a time (easier to keep track of). Replace unit on base and check for leaks before replacing refrigerator. Other than cleaning, the task took about 20 min. and was simple. The cleaning, on the other hand...