ART2527AB (PART2527AB0) Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Lancaster, PA
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
water leak and frezes ice in bin
to easy to describe, remove 3 screws and a wire plug then install new unite.
Works great
Thanks
Works great
Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Northglenn, CO
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Not making ice, and water leaking in freezer
Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness
Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on
ALL FIXED!
Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on
ALL FIXED!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Arvada, CO
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing crisper drawer support post
I recently bought an old Amana refrigerator for my garage on CraigsList for 75 bucks. It was in great condition for its age, but was missing the post that supports the fruit and veggie crisper drawers. I did a Google search, quickly found PartSelect, and just as quickly located and ordered the missing part, which was reasonably priced. PartSelect promised it woud be delivered in 3-5 days by FedEx Ground and it was. I took it out of the box, removed the crisper backets - and glass cover for them - installed the post and WHA-LA, the crisper backets work just as good as when the fridge was new! Couldn't have had an on-line mal-order operation go any slicker!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from manvel, TX
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker flaked and leaked leaving big glob of ice
Unplug wire harness back of fridge. Unscrewed 4 screws on guide for ice bin. then unscrewed two screws holding ice maker to wall of fridge. removed ice maker. then had to take front cover off (pull hard, it comes off) and remove wire harness plug from the ice maker. save this, front cover, and all hardware to re-use. reverse steps to reinstall, including wire guide that goes up and down to stop and start ice maker when bin fills. Have to put this into front part of ice maker correctly for it to work. make sure it is down so that it will produce ice. ice tray took a few hours to fill with water initially, must be on a timer or something.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from COLDSPRING, TX
- Parts Used:
- D7824706Q
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice tray filled up with water. Stopped making ice.
As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from GARNER, KY
- Parts Used:
- D7824706Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
I went by the video but my removal and installation were different than shown.
Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from ABINGTON, PA
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Icemaker made some pretty sad cubes! Hollow, unfilled, or small cubes
Replacing the icemaker is pretty simple. Three screws, an electrical connector. Hardest part is getting to the icemaker since the freezer is below the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from GRANTS PASS, OR
- Parts Used:
- WPW10189703
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
TOO COLD FREEZER, TOO WARM REFRIGERATOR, EVAP FAN FROZEN SOLID
I just followed the directions on the video of my specific model. Make a note of where to locate that video of your model, as there are many other videos of other models that can have different parts located in different areas and it can be time consuming finding the exact video you want again.
Also note that you must make mental or written notes on exactly what direction any parts you remove are facing, this can save huge amounts of time when reassembling.
I was worried that I might need other parts, but decided to do one part replacement at a time since this unit is a spare and no urgency to get it back working again. I found that the evaporator fan was the only thing needed! The fridge works like new again!
Also note that you must make mental or written notes on exactly what direction any parts you remove are facing, this can save huge amounts of time when reassembling.
I was worried that I might need other parts, but decided to do one part replacement at a time since this unit is a spare and no urgency to get it back working again. I found that the evaporator fan was the only thing needed! The fridge works like new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Wiggins, MS
- Parts Used:
- WPW10189703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The freezer worked fine but the refrigerator wasn’t getting cold.
I removed the flat panel inside freezer & fan blades not turning. I removed 2 1/4” screws, unplugged wires took fan motor out & put that fan blade on new fan motor. Plugged wires into new motor replaced 2 bolts, reinstalled flat panel plugged refrigerator in & reset temperature controls. The next day checked temperature and was all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from Indianapolis, IN
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker Leaked Creating an Ice block
Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackson from Leesburg, VA
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replaced leaking ice maker after minor screwup!
Old ice maker leaking water and produced ice cubes with black inclusions. First, I removed old ice maker per video instructions. Transferred electrical cable, cover, and bail to new ice maker. First installation failed because I failed to make sure water tube correctly enter back of ice maker. No ice. Initially thought electrical cable wasn't firmly in place. Then I noticed frozen water dripping down back of freezer. A clue! Removed ice maker and reinstalled making sure water tube went through the hole in back of ice maker. Now the new ice maker works beautifully!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Golden, CO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this instruction helpful to you?
Thank you for voting!