59669274990 Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- david from bondurant, WY
- Parts Used:
- WP10442411
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
refrigerator was getting warmer.
first thing i thought was the condenser was plugged so pulled out and cleaned with shop vacum backwards so it became a blower not a vacum cleaned it good and put together. wife noticed cracking noise inside freezer. took all freezer food and shelfs out. took 1/4 inch hex nut screws out and found complete condenser solid ice. did some research on internet and found parts select stories. i buy passed thermostate and hooked heating coils direct which then thawed condenser. checked timer by turning of and it worked fine until i got part and installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Albuquerque, NM
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
lights wouldn't come on/work in refrigerator
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aliki from Miami, FL
- Parts Used:
- WP628356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill cup broke.
Very easy to order from parts select. Took seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from NORTHRIDGE, CA
- Parts Used:
- WPD7813010
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker not producing ice
The parts were very easy to replace, however I am still without ice and cannot figure out why. I have ohm tested the contol unit and everything works fine, I am able to jump it and turn on the motor and water fill valve. Any suggestions?...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from DAVISBURG, MI
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped making ice
Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sue from avondale, PA
- Parts Used:
- 10880202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Piece broke off of meat drawer gilde rail
I removed the screws holding the side onto the drawer, removed the side, placed the new one on and put the screws back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from ARLINGTON, VA
- Parts Used:
- WP67005140
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom-freezer handle had a horizontal crack
Unscrewed the old handle, cleaned the area, and screwed on the new handle. Simple, and took just a couple of minutes. Our kind of repair!
The handle is now whiter than the rest of the fridge, but (1) were just happy to even find a replacement handle so we could switch it out and (2) no longer worried about it breaking and our having to purchase a new refrigerator just for that reason, when this one is still working just fine. Thank you, PartSelect! (We have referred friends to you :-)
The handle is now whiter than the rest of the fridge, but (1) were just happy to even find a replacement handle so we could switch it out and (2) no longer worried about it breaking and our having to purchase a new refrigerator just for that reason, when this one is still working just fine. Thank you, PartSelect! (We have referred friends to you :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryln from SANTA ROSA, CA
- Parts Used:
- WP67005140
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Original handle was loose.
Removed broken handle and replaced with new one by inserting 2 screws. Just took about 2 minutes and is a great improvement!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VESTAL, NY
- Parts Used:
- W11176463
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Old fill tube was blocked
Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- riley from CAVE CREEK, AZ
- Parts Used:
- WP65889-4
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Refrig began to trip the GFI circuit in the garage. When plugged into a house interior circuit the lights and fan ran but no cooling in either the freezer or frig.
First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Refer to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Winston A from Brooklyn, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Raplaced switch
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Brookfield, MA
- Parts Used:
- WP12550116Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
ripped seal around freezer door
The repair went very well. Once the sockethead cap screws were taken out of the seal and the ripped seal was removed, the door panel separated from the door itself allowing me to see that ice had already been forming within the insulation. I was fortunate to have decided to replace the seal when I did or further damage would have occurred. After thoroughly cleaning the refrigerator and freezer I replaced the seal using a hair dryer as suggested to tighten the seal into place. Everything is working as it should once again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from Wells, MN
- Parts Used:
- WP67005141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
freezer door handle was cracked.
replaced the handle with a new one. Very simple. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- IRMA from SAN DIMAS, CA
- Parts Used:
- WP67005140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken freezer door handle
unscrewed old handle and screwed in new one, whalaa. thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Brownstown, MI
- Parts Used:
- WP12013209Q
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Noisy Condensor Fan
I think spent more time removing the frozen food and cleaning the bottom of the freezer compartment than actually changing the fan.
it came in one well constructed assembly, fan motor and bracket - an exact match for the existing part. I did not have an ice maker to remove so the steps were pretty simple.
1) Remove ice cube tray holder
2) Remove about 8 screws that hold the condenser cover plate
3) Remove two screws that hold the bracket (fan is attached to bracket)
4) Pull bracket away and remove two green ground wire tabs
5) Remove power connector
6) Clip wire ties from bracket that hold power cable
7) Remove old part
8) Reverse procedure
The old part had some built in wire tie holders that held the power cable away from the fan. I had no problem using a normal wire tie to tie it out of the way. You can probably just fed it around without a wire tie and achieve the same results.
All in all a real easy job. I'd say the job was easier than replacing a door knob, but harder than putting on new wiper blades.
Should be no problem for someone with average handy man skills.
it came in one well constructed assembly, fan motor and bracket - an exact match for the existing part. I did not have an ice maker to remove so the steps were pretty simple.
1) Remove ice cube tray holder
2) Remove about 8 screws that hold the condenser cover plate
3) Remove two screws that hold the bracket (fan is attached to bracket)
4) Pull bracket away and remove two green ground wire tabs
5) Remove power connector
6) Clip wire ties from bracket that hold power cable
7) Remove old part
8) Reverse procedure
The old part had some built in wire tie holders that held the power cable away from the fan. I had no problem using a normal wire tie to tie it out of the way. You can probably just fed it around without a wire tie and achieve the same results.
All in all a real easy job. I'd say the job was easier than replacing a door knob, but harder than putting on new wiper blades.
Should be no problem for someone with average handy man skills.
Was this instruction helpful to you?
Thank you for voting!