59669272990 Amana Refrigerator - Instructions

Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

First unload the doors, and remove each door from the fridge and freezer. I placed the doors on the counter island and removed all the screws from around the perimiter with the battery drill. Lots of screws. The freezer door had some Ice accumulated in the insulation inside the door. I salvaged as much of the dry fiberglass and tossed the wet stuff. I cut some strips of fiberglass from a roll of 3.5" I had to replace the tossed insulation. The door seal installation went smoothly and the door rehanging was easy also.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

Very easily removed the nuts holding the gasket to the door. Previously took new gasket from packaging and used a hair dryer to smooth the wrinkles from it, about 5 minutes. Installed the new gasket and adjusted the seating of the actual freezer door, for a proper fit. Now there is no snow in my freezer and the poor compressor only kicks on maybe ten times a day, as opposed to most of the day. Not to mention what the savings in electricity may be and extended life for my Amana. Should have done this two months ago. Service and shipping from Parts Select is second to none, with a website interface that makes sense- try most of the other online retailers and you will know what I mean.

First I removed all the screws with the exception of the top row, these I just loosend.I made sure how the old one was installed before I removed it.I then used a hair dryer on the new one briefly to take out the shipping kinks.I removed the old one and put the new one in with a little adjusting as i went. I then put all the screws back in,adjusted it a little more and finished by snuging up all the screws.It was very easy and works like new.

Turn freezer section control wheel off, unplug unit. Then remove all items/baskets from freezer to allow access. Use nut driver to unscrew 3 screws on control plastic housing. Drop down housing from top and unplug wires (note correct locations) from control wheel switch. Remove screws and ground wire from metal backing plate to plastic housing. Push or pry the 2 metal holdtabs down carefully to allow the 2 plastic housing tab fingers to be pushed inwards to seperate metal plate from housing. Pry control wheel off from switch arm with screwdriver. Remove switch and replace with new one.
Use the reverse order of removal above to replace into freezer but use caution when replacing wheel onto switch arm and plugging in wires. Remember to carefully pry the 2 metal tabs back up to secure the plastic finger tabs in place.
Job done.

I removed the Icemaker then the backpanel in the freezer. The fan motor removal required only to hex screws and three wires to dismount. The biggest problem I had was the replacement motor had the connecting pins for the wire harness on the reverse side. I thought I could unbolt the motor and flip it but this did not work. I remounted the new motor and was able to get the wires connected. The thermostat clipped in place but one of the wires had a different connector than the new unit. I used a wiring snap connector to complete the connection. The defroster timer was under the refridgerator and after taking two screws off the cover plate was just an unplug and plug in the new unit. When I first turn the unit back on nothing happend. I soon realized I had to advance the timer until the unit kick on. It has worked fine since and solve both the noise problem and defrost issue.

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

I hired someone to do this, but after watching him do it, this is an easy job. Amana made a smart refrigerator and it's easy to do your self. I saved a LOT of money buying the parts here and I should have attempted it myself. The trick is heating up the gasket once it was mounted and then when you had a tight seal to the door, tape the door shut and LEAVE it as many hours as you can (minimum of 4, but overnight better).

1st remove the gasket from the packaging & let it get to room temperature . 2nd use a hair dryer to get it in shape . 3rd cut out a piece of the box that the door gasket was delivered in to cover the freezer opening after you remove the door,4th(remove the door by removing the bottom hinge) 5th put the door on a table to remove the old gasket with a screw gun,(now is a good time to clean the door up) after the old gasket & panel was removed I found the insulation inside the door panel frozen solid so I replaced it .If you don't replace this fiberglass insulation or a least try to thaw it out you defeat the purpose of the doors insulations R value. 6th replace the gasket (replace the gasket the same way that you removed it) 7th put the door back on the freezer.You don't have to remove the freezer door to do this job but it makes a much neater job & a better seal when the door is closed. This isn't the 1st door gasket I replaced so I kind of knew what I was doing.Good Luck

Removed the hinge cover, removed three hinge screws, removed door. Then I used a screwdriver to pry out the hinge bushings, pushed the new ones in and replaced the door. Both Maytag and Lowe's (who held the extended warranty) said that the door was not a repairable item and would have to replace the whole door. Since that would cost more than the value of the fridge, they voided the warranty and returned my cost. Too bad we didn't know about Part Select, we would have held their feet to the fire.

I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.

First step, call the repair man. He listened, and then said to get a new refrigerator, since this one is 28 years old and the repairs could amount to a significant part of the price to buy new. Even if he fixed this, it could develop other problems, yada. So we went out to buy and discovered nothing suitable that would fit in that slot of our kitchen! We'd need new counter top and cabinets to fix this problem! So we went to the Internet and searched to find the likely source of the problem and the parts schematic at PartsSelect.com. Yah! We ordered the part, and then found we had no idea how to install it. Sooo, back to the Internet, and eventually got some good clues - it goes in the kick space under the front, and just plugs in, once you can get to it by removing the bracket that holds it. Working underneath a refrigerator is not complicated but it's awkward. The form of the new timer was not exactly the same, but it does function correctly. We have no experience whatsoever with appliance repair, so pretty amazed at our success. This old Amana looks very good inside and out and is now working perfectly again. If it lasts a few more years, we will be thrilled to have spent $15 to save $500. We can always buy new later on.