GTA18B2L (P1192602W L) Amana Refrigerator - Instructions

First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!

Service and shipping were fantastic! I would definitely use Partselect again!

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

It was a complete mess and a failure. There were no in structions with the gaskets except warming them in water to streatch them. Nothing with a photo of what the gasket looks like as it is being installed or after installation. I am still not convinced they are the correct gaskets for the model. It was a total waste of time and $130.00 to try to replace the gaskets. In the end, I determined that it would be cheaper in the long run to buy a used refrigerator than to mess with the gaskets.

Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.

I first loosened all screws that are hidden by seal leading edge. I then removed seal. I made sure that I knew which side of seal was to be in contact with refrigerator door frame to provide the seal. I positioned the seal on the door inner panel starting at the top. After I had finished positioning the top I proceeded to position both sides and then the bottom. I tightened the screws only enough to hold the seal in position. After I had the seal in the proper position I tightened the screws that hold the seal in position. I used a hair dryer to heat seal and smooth out the the sealing edge.

I didn't. Don't know how to get to light bulb to change it for this specific model

simpley place the support into slot provided.

proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

I removed all the screws except the top screws. These screws I loosed to make sure the door shelves remained in place. I did not want to remove the refrigerator door. I had read this method on PartSelect. It worked fine. I would recommend a power drill because of the number of screws supporting the door shelves; a power drill really help.

Please note there are only 3 sides of the "new" door gasket that are magnetized. It would have been nice to identify which are the magnetized sides before I did the installation; I guess I should have read the directions before hand.

It was an easy job.

My friend tore into the thermostat and found it no longer was working so we go onto the chat line askeing questions and ordered the part expecting it in 4-5 days standard delivery. The part arrived in two days. He attached it quickly and it is working perfectly. I will order again if I have appliance problems. I love the chat thing. Repair time with tare down and put back together probably less than one hour.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

The hardest part of the repair was how to remove the panel the part was behind. Once we figured out where it was (behind the temperature controls in the front of the refrigerator), it was very easy to take out the old & install the new. Works perfect now.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

I removed the cover over the light and disconnected the wires and replaced the socket.