1999CIW (P1115102W) Amana Refrigerator - Instructions

Used socket set to remove screws. Removed the wire harness, then removed lift arm from old ice maker and then put lift arm on the new ice maker. Reinstall wire harness then installed back in freeze with the screws. Video was very helpful. I will do business with Partselect in the future. Shipping was very fast. Thanks Partselect

I didn't. Don't know how to get to light bulb to change it for this specific model

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

Shut off the water supply at the wall then using a 1/4" nut driver I removed the steel and cardboard backing plates from the rear of the refrigerator. Disconnect the main water supply hose and then the two water lines for the chilled water dispenser and ice maker. Remove the two screws on a support bracket which holds the valve in place.
Reassembly in reverse order.
The process was very easy and took no longer than 15 minutes and works just like new. This is a good time to do some thorough cleaning around the fan and coils to keep them working properly as well.

Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same time to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

Tried to repair existing valve which I have succesfully done many times by cleaning and removing grit from internal neoprene parts until new parts received. Was not successful. New valve worked perfectly. this is only 2nd repair needed on this ref. since new. 1st was defrost timer. Ice maker hasn't missed a lick since new.

First I turned the water off behind the refrigerator....took the ice maker inlet valve off, put on the new one. As simple as that & it is working beautifully....not only am I a woman but 55 yrs. young too!
With the right part & right tools NOTHING is impossible & I saved myself a repair persons fee!!!

pulled cover off back of refrigerater at the water line,shut water off removed water line,check for pressure at the line by puting the line into a 5 gallon bucket it was ok.took the dispencer lines off that goes up to dispencer,hit dispencer switch could hear buzzing at the dispencer unit but no pressure.so i replace water inlet valve

For the icemaker, I removed the ice tray and loosesned the two attaching screws(1/4"). I removed the lower bracket and then removed the ice dispenser motor cover below the ice maker. This made it easier to remove the wiring harness. After removing the icemaker from the refrigerator, I swapped out the wiring harness and ice detector bracket (wire bail that swings). Hooked things back up and went on to the water valve. All in all about 15 minutes and pretty easy.
For the ice valve, you must turn off the water supply, disconnect the power plug and move the refrigerator away from the wall. (Now's a good time to clean out under and behind the unit!) Remove the valve from the base with the 1/4" nut driver. Remove the inlet line(standard hose fitting).Have a sponge handy. Remove and replace the new valve in the bracket by popping the clip off and on the new one. Replace one outlet line and electrical connection at a time (easier to keep track of). Replace unit on base and check for leaks before replacing refrigerator. Other than cleaning, the task took about 20 min. and was simple. The cleaning, on the other hand...

Pulled out the fridge fro the wall, unpluged it, turned off the water supply to the house, disconnected the water line to the part, installed new part and re-attached the wires and ground, turned on the water - no leaks, plugged in the fridge - ice maker begand to fill and has continued to work.

Easy as pie. Will contact you again if I have other appliance problems.

Paul M, Seattle WA

turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert thermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.