59669879991 Amana Refrigerator - Instructions

replaced the handle with a new one. Very simple. Very easy.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Pull refrigerator out from wall to shut off water and power. Remove ice bin, pulling front down then out. Remove screw at bottom of icemaker, then pull down to release two clips, Pull out a couple inches to get hand behind icemaker to release wiring harness connector. (squeeze top and bottom to release clips). Remove unit. Remove wiring harness and wire bail from old unit and install on new unit. Reverse steps to install new unit. Make sure ice bin is fully inserted, or unit will not function.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

After checking the water valves ordered new ice maker. received the part three days after ordering! Clearing out food, removing the old one and installing the new unit took under 15 minutes. Everything went fine.

I read the previous repair story and agree with the author that the screw behind the front piece was difficult to remove and re-install. If I had a magnetized nut driver I think it would have been easier. There were no installation instructions so I relied upon the repair experiences. The other two screws came out easily and I found the harness release easily and the harness was easy to reinstall.
I am not a good handyman but was able to install the new ice maker

Most difficult part was finding where they hid the defrost timer. (it is in the left front under the fridge behind the kick panel.) just unscrew the two fastener screws from the front, tilt fridge up on one side, slide timer bracket back and remove. Unplug and remove timer from metal bracket. Replace timer and remount bracket.

, to remove the inlet tube holder/guide gadget thingee: (1) remove the three Phlipscrews from the motor end of the housing. (2) pull the housing straight off the end. (3) remove two Philips screws in deep holes that hold the ice tray onto the motor housing. (4) this frees the ice tray assembly, which you have to pull out, freeing the rotating blades, from which (5) you slide the sxle out of the middle of the inlet-tube thingee, so (6) you can then remove the inlet gadget from the ice tray.

You then reverse these instructions to reassemble with the correct inlet gadget. The tricky part is the front cover that hides the ice-tray from view. That cover has a couple of ears that have to fit into mating holes in the motor housing before you replace the two deep-hole Philips screws that hold the tighten the ice-tray assembly back onto the motor housing.

So it's too bad they don't see the ice-maker assembly with all the knock-outs inplace, so you can knock out the one you want. Other than that, it would have been no more trouble than other people have reported in working in the tight space inside the freezer compartment.

Unplug refrigerator, remove ice maker if you have one, all you need is a 1/4 " nut driver or socket. I used a 1/4" drive socket set with a1/4" socket. After the ice maker is out of the way, remove the panel on the back of the freezer to expose the fan. Remove the 2 screws holding the fan in place , and disconnect the wires that are plugged on to the connectors. Remove any ice that has built up around the condenser and install the new fan. Plug the refrigerator back in to insure the fan runs. If it works, unplug refrigerator again and install the panel over the fan, and install the ice maker again. Plug the refrigerator back in and put all your frozen food back in the freezer. That's it , Simple!!

only problem was many screws -- like 30 or so -- took a while to get off without a socket wrench and then get back on -- all while the freezer was dripping. Had to do it over a period of time.

I was so happy to find a gasket still available for my old refrigerator. This was an easy job, more time consuming than anything, taking out the many screws that held the old gasket in. I am a 74 year old woman, so if I can replace a gasket, I think anyone can. I removed all the screws around the old gasket and pulled it off. Cleaned up the door area with a damp cloth. Soaked the new gasket in warm water to make it pliable, laid it around the door frame, making sure the lip was under the screw in area. I fitted each corner first. Then I started screwing the gasket in place with the old screws starting in the middle of each side. I slowly worked my way around the freezer door until it was done. Easy repair and saved the cost of a new fridge.

installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

I REFERENCED A PARTS SELECT U-TUBE VIDEO ON HOW TO REPLACE A FREEZER DOOR GASKET. (GOOGLE SEARCH "HOW TO REPLACE A FREEZER DOOR GASKET"). THIS MADE THE PROCESS GO QUITE SMOOTHLY.