GT2122NDEW Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- michael from Hoffman Estates, IL
- Parts Used:
- WP61002112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken End Cap
Simply replaced part. Press fit shelf retaining bar back into place. I was just glad you had this obscure part which was easy to find on you website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Sacramento, CA
- Parts Used:
- 61002532
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
While cleaning, I shattered the glass shelf!
Like many others, I removed all the shelves/pieces to the refrigerator for cleaning. While handling the 'Crisper Shelf Glass', I slightly tilted the shelf and the glass fell out and shattered to pieces. I was mortified; the shelf itself was fine, but I had no clue on how to replace the piece of glass. So, I was really glad to find partselect.com. The website was so easy to use so I could find my model number and it had the best price around! Also, I put in my order Monday morning and I received my part the next day (Tuesday morning)! The glass fit into my refrigerator shelf like a glove, it was perfect! It required no tools and it took less than a minute to fit in. Thank you so much for your amazing and speedy services! I am a very satisfied customer! I will definitely be recommending your services & products.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Williamsport, MD
- Parts Used:
- W11045462
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower shelf holder kept falling out
Removed keeper on left side, slid trim into keeper on right, attached left keeper to trim, re-inserted keeper onto door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph T. from Morgantown, WV
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch went bad
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- douglas from surprise, AZ
- Parts Used:
- W11045462
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door trim bent and ugly
Just removed old trim and attached new trim by hand. good results. Happy with your product and tmeliness of delivery Thanks Doug Salter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Metairie, LA
- Parts Used:
- WP61002112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator door shelf end cap was broken
I love how easy it was to find out what part I needed by seeing the photos to verified it was the part I needed. The repair was super easy and the directions were easy to understand. I didn't even need tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from sonoma, CA
- Parts Used:
- WP61002112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken cap ends
put the end caps on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristy from Yarmouth, ME
- Parts Used:
- 61001920
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Hinge between the freezer and refrigerator door broke
Removed the freezer door and replaced with the new hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from St. Pete Beach, FL
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broke the arm off the food compartment rocker switch
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Arlington, MA
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Laramie, WY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Switch didn't work
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dora from Rock Island, IL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light would come on and off
Viewed the viedo - it showed what to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Traverse City, MI
- Parts Used:
- WP61004009
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Freezer continually had ice build up
Replacement would have been easy except there was so much ice built up inside the door. Should have just turned it off for 48 hours to let ice melt. Instead completely disassembled door to remove ice.
Was this instruction helpful to you?
Thank you for voting!