GB2526LEKS Amana Refrigerator - Instructions

Popped off the control panel at the top behind the door. Found the thermistor and replaced it, cutting the wires and splicing the new one in. Immediately the warm section of the refrigerator was getting below freezing temperature readings, so the cooling vent was not opening. I put the old one back on and the temperature readings went back to being accurate. So this was not the problem. I believe now that the fan somehow is not blowing enough cold air up. So now I'll probably buy a fan motor and maybe a blade and try that. Otherwise the computer module I priced at $500 so I hope it isn't that. I replace the fan motor a few years ago already.

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

I was getting small sections of ice and a snow like build - up around the freezer door. I thought that the door was not sealing tight enough and that the cold air was leaking out. The original door gasket appeared to not have any flexibility anymore and was getting hard. I ordered a new door gasket from PartsSelect. When the gasket arrived it was in a large enough box and that saved me some time as the gasket was not "crushed" to the point where there were a lot of kinks in the gasket. I used a hair dryer on low to warm the gasket and stretch it out some. The freezer door required me loosening four small screws and lifting the door off. I placed the door on an old blanket so not to scratch the finish. It was easy to remove the old gasket and after doing so I cleaned the track where the new gasket was to go with isopropyl alcohol, Once cleaned, I placed the gasket over the channel in the door where the old gasket had been and started installing the new gasket. I started at the corners and you can feel the gasket snap into place. Once the four corners were done I started at the top and installed the gasket the rest of the way. You can feel it snap into place. as you work your way around the gasket channel. Once the gasket was in place I placed the door on the four small grooves where the door had been and tightened up the screws. I made sure that no white from the inside of the freezer door was showing after the gasket was in place and that the gasket had some "spring" to it. The door was back on, the gasket was tight and it appeared to be a good seal. Around 12 hours later I checked the freezer and there was no more ice or "snow" on the edges of the freezer. While the gasket was not inexpensive, it is a genuine OEM piece, and the gasket is a lot cheaper than a new refrigerator!
I hope this was helpful...

proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

1. Turn your water OFF and pull the refrigerator out from the wall so you can access the back.
2. Use pliers to remove tubing clamp.
3. Remove old water fill tube.
4. I used a putty knife to gently pry out the old fill tube from the back of the refrigerator. Once the fill tube pulls out about 1/4 to 1/2", then you can gently pull the remainder of the tube out by hand. Once I removed my "old" fill tube, that is when I saw the "ice plug" that was causing pressure in the water supply line and caused my water line to pop off.
5. Install new fill tube. The end that goes in first needs to go through a small "ring" inside the freezer (this "ring" is not encountered until the fill tube only has about one more inch to be inserted into the back of the refigerator. I could barely see this "ring" if I opened the freezer drawer and stuck my head in as far as I could. I had to gently rotate the new fill tube until it cleared the "ring". You will feel some resistance until it lines up properly.
6. Snugly push in the part that stays on the outside of the refrigerator until it looks like it is sealed.
7. Gently push up the water fill tube where it belongs in the new part and replace the tubing clamp.
8. Turn your water on and make sure there are no leaks (I left my refrigerator out for about an hour).
9. Push your refrigerator back in place.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

I broke the glass in the frig and found partselect and ordered the new glass and had it in 2 days. Very fast shipping.

Removed and replaced with new part.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

I initially tested the heating element and defrost thermostat using an ohm meter. the defrost thermostat was incased in ice, so I replaced it first. The refridgerator worked for about a week and then froze up again. I then replaced the thermistor and the unit is working as designed.

Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.

Don't try and remove the front/handle from the broken pan, you will break it and its double the price of the pan, just use the small hammer to break the pan into smaller pieces and remove handle from them then the handle will just snap onto the new pan. Piece of cake!

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!