59661152100 Amana Refrigerator - Instructions

First I removed the 14.3 tons of freezer contents, closed the water valve, shut off the juice, and removed the freezer bins, the freezer door and the three screws that held the element in place. After bringing in 397 hand tools from my garage inventory, I loosened the unit and, after extensive evaluation, I finally disconnected the wiring connector from its freezer rear wall connector counterpart. You ain't gonna believe the rest of my story--of total ineptitude by an experienced fix-it-yourself dummy.

I searched the internet for a replacement ice maker and found it at partselect.com. I called Sears to ask if I could add my refrigerator to my existing appliance repair account. Sears said sure--it would cost me only one arm, three toes and one grandchild. I abruptly declined their magnanimous offer—I don’t give up my arms and toes so easily.

I visited the local Maytag repair parts and service retailer, who advised they didn't do parts anymore. Expecting their repair price would be greater than Sears, I resorted to partselect.com. I called them to be assured what I was buying was not mistakenly a 747 Landing Gear. On the afternoon (West Coast) of 4/28/10, I ordered (via internet) one PS21215123 Ice Maker Assy. Much to my pleasant surprise, it arrived via FedEX on 4/30/10 (no freight charges to me).

My repair/replacement efforts were hampered by the effects of my right rotator cuff surgery a few months before and major left wrist surgery two months ago to remove fractured bones and torn ligaments.

Undaunted by my physical handicaps, I forged forward. After re-installing the unit, I turned the water supply and electricity back on. It was graveyard dead. I wisely then bought two bags of ice as an interim solution to the severe needs of my wife and me for our daily chilled evening cocktails. I removed the unit, checked it out and re-installed it. I bought two more bags of ice. All the while, I turned the water and electricity off and on as required by reasonable safety standards. High tediousness!

Several more home maintenance tasks then arose for Sergeant Super Fixer, but I returned to the ice maker problem on 4/8/10. Last chance--remove the device and insure there was no frozen ice in the inlet tube--or call the local partsless repairman. No ice found, but I did learn the wiring connector to the unit was awry--no contact! While explaining that to my wife, I realized the two upper mounting screws were intended to be partially installed into the freezer wall to accommodate the unit's slotted mounting holes! Then, tighten the screws. Oh my God! During my 143 installations and removals, I had installed those screws blindly--using the (handicapped) skills of my right and left hands without any benefit of direct eyesight.

I returned to my challenging project this morning (4/9/10), fully utilizing all the expertise I had gained yesterday. Fifteen minutes of amusing effort! Turn on the juice! Turn on the water!Two hours later, ice cubes were dropping into the bin like rhinoceros bisquits in the jungle.

Hallelujah! I now am free for the next challenge!

HINT: Put a bed pillow (an old one, or your wife's) in the freezer compartment to soften the harshness of its cold metal on your back, if you use the "crawl in on your back" approach.

Turned off water supply, removed old Water Valve, installed new Water Valve, turned water supply back on. After first couple cycles of icemaker, increased water pressure by opening water supply valve one more full turn. Good cubes! Job completed in about 1 hour - moving fridge out, swapping Water Valve, moving fridge back in. (time to clean coils not included)

I removed the shelves from the freezer. I unscrewed 6 screws with a 1/4" nut driver and removed the back panel. The coil was solid ice because the defrost cycle wasn't working. I thawed the ice with a hairdryer (5 minutes), unplugged the thermostat and installed the new one (it simply clipped on to the coils), and reassembled the back panel and installed the shelves. Total time, about 14 minutes. Total cost, less than $20.00. I can't even get an appliance repairman to show up at my door for less than $100.00! Thanks to your website, I was able to diagnose my problem, order the correct part and fix it myself! (I bookmarked your site under my favorites). Thanks for this great consumer service. It's easy, inexpensive and quick to do it yourself!

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse panel. ( 20m). i also took time to clean grilles with small vac and damp rag, ( looks and sounds like new) bob Wi.

I noticed the the freezer was beginning to thaw out and the refrigerator was no longer cooling. Due to the age of the refrigerator I thought that it couldn't be anything too major so I sought out some advice and order the necessary parts through partselect.com The problem was the thermostat in the freezer and changing out was pretty simple. The website offers some good advice along with quick delivery which makes attempting the repairs worthwhile. I would definitely use partselect.com again for any other appliance repairs!

Other stories I've read here speak to difficulty of changing a gasket with the door on the appliance. Whoa! Take the door off, tape cardboard over the opening, lay the door on its back and proceed. You will avoid racking or twisting the door and having the new gasket fit worse than the old. You can also thaw ice which often forms inside a door over time. Reinstall the door taking pains to shim properly so the new gasket is not overcompressed or allowing a gap. A dollar bill is a good gauge. It should resist a bit as it is pulled out after closing the door on it. This was not exactly step-by-step, just offered as advice from a whole bunch of experience.

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

This is a bottom freezer refrigerator. First I unplugged the refrigerator. I then removed the wire shelf and wire tray from the freezer. I then removed the ice maker be removing the three screws that hold it in place. I then disconnected the icemaker electrical connector. I then removed the 7 screws that hold the panel at the back of the freezer revealing the evaporator and heat exchanger. I then unclipped the icemaker wiring harness from the panel. The whole evaporator/heat exchanger was buried in ice. I defrosted it with a hairdryer. This took about half an hour. The bi-metal thermostat is attached to the heat exchanger by a clip. Be sure to wear latex gloves to prevent cutting your fingers on the aluminum fins. I disconnected the electrical connectors and then carefully unclipped the thermostat. I discovered that the new thermostat had spade connectors where as the original had one spade connector and a bullet connector on the brown wire. I reused the original bullet connector by cutting it off the old thermostat and splicing it onto the new thermostat. I reversed the process for reassembly. There is no longer any ice build up and the refrigerator is working normally.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

unplug Ref. and on back of Ref., take back panel off to locate compressor. Attached to the compressor are 2 small parts, secured to the Ref. w/ a small clip. Remove the clip w/ a pair of plyers. Remove the Capacitor (white plastic electric part)form the Compressor - the black overload relay will come off with it. Plug the new relay in to the Capactor. Locate the two wires (used to connect the Ref. to the Capacitor) from the Ref, unplug them from the old Capacitor/Relay and plug them in to the new part(s). Plug the new parts back in to the Compressor. Reinstall the the small metal clip that holds the Capacitor/Relay in place. Plug Ref. back in - if no noise, parts have worked (allow 5+ mintues to test).

My husband replaced the condenser fan. It took awhile and a few choice words but he got it replaced. The fan seemed to work fine, but it still wasn't cooling. I noticed that when we had the fridge unplugged that water started draining out the dials at the top of the fridge under the freezer. And there was absolutely no water at all in the drip pan under the fridge. So I took the doors off and totally took the inside of the freezer apart. I discovered that the styrofoam on the floor of the freezer had become inudated with fluid and the under the foam the coils were all frozen solid with ice. Hence not allowing any drainage. I put a lamp in the freezer area and defrosted all the ice. In searching the internet i discovered that they no longer produce the foam so i went to home depot and got a piece of foam and aluminum foil and cut it to replace the ruined foam. I put the fridge all back together said a prayer and crossed my fingers and lo and behold it works perfectly now!!!!

Remove the back hardboard cover screws for access to the condenser fan. I opted to tip the fridge over on its side for even better access to the fan mounts and wire. Replaced the fan assy (reused the fan). Splice the wire and it's done.

very easy.....
1. removed the food items from the shelf
2. raised the shelf and removed the broken support post
3. inserted the new support post and guided the drawer rails to rest in the new support slots
4. cleaned the glass shelf and replaced the food items
5. made my wife very happy now that the veg drawer opens and closed like new.

First I removed the Ice bin, I then loosened the ice bin rail under the ice maker and removed the screw that attached the bottom of the ice maker to the side of the fridge. I unplugged the power to Ice Maker from the back of the fridge and unscreewed the two screws that secured the ice maker to the fridge. This allowed the Ice Maker to be removed from the fridge. To replace the new ice maker I simply repeated the steps in reverse.