59669147992 Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Choctaw, OK
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
freezer will not freeze or cool the ice box
I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Cupertino, CA
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The ice maker stopped making ice.
I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Rockwall, TX
- Parts Used:
- R0131577
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Not Defrosting
Disconnected power cord, Removed lower front face plate, removed one screw that helt cover over defrost timer, removed two screws that held timer, unpluged timer and removed it. Replaced old timer with new timer. Replaced timer installed two screws and replaced cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Ruth, MI
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My old icemaker lost some of the nonstick surface and the ice didn't want to come out
I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duncan from Metairie, LA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Switch Broke...Absolutely Fell Apart.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linford from Cedarville, NJ
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker would not fill with water.
Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Sierra Vista, AZ
- Parts Used:
- WP10530204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper rubber seal tore off
Pulled off old ones and warmed new seals in warm water first to make it easier to slip on. Then I just pressed them on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Valley Grande, AL
- Parts Used:
- WP67005140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Appliance has Freezer on bottom and Someone dropped Item on handle a broke it
2 Screws on and off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- R from Cranford, NJ
- Parts Used:
- W10752646
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Freezer cooling cycle became warmer
There was water on floor at front and ice cubes in freezer were wet.
Freezer cooling cycle had become warmer.
Received part. disassembled the temperature control; i.e., pulled off the control knob; removed 3 screws holding unit to top of freezer; pulled two wires from their connectors to the old "control unit"; pushed them onto the connections of the new unit; reassembled the control to the top of the freezer with the three screws and pushed on the control knob.
bybob
Freezer cooling cycle had become warmer.
Received part. disassembled the temperature control; i.e., pulled off the control knob; removed 3 screws holding unit to top of freezer; pulled two wires from their connectors to the old "control unit"; pushed them onto the connections of the new unit; reassembled the control to the top of the freezer with the three screws and pushed on the control knob.
bybob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Windsor, CA
- Parts Used:
- 833697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
refrigerator not cooling properly
Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dave from williamsville, NY
- Parts Used:
- WP67005140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
half of the freezer handle broke off
Not much to describe. Just used philips screwdriver and removed the two screws holding the handle in place. Discarded the broken handle, washed the area where the original handle was and replaced it with a brand new white handle (not yellowed with age)by replacing the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Las Vegas, NV
- Parts Used:
- WP628356
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Water Fill Cup Broke
The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Severn, MD
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice Maker was leaking
Used socket set to remove screws. Removed the wire harness, then removed lift arm from old ice maker and then put lift arm on the new ice maker. Reinstall wire harness then installed back in freeze with the screws. Video was very helpful. I will do business with Partselect in the future. Shipping was very fast. Thanks Partselect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D K from Stratton, ME
- Parts Used:
- WP10442411
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
On and off the fridge wouldn't defrost properly
Did the troubleshooting with online instructions and a multimeter. Bought the new thermostat. Disassembled the freezer compartment using a nut driver to expose the evaporator, etc. The thermostat was easy to locate in the upper right hand corner. The new thermostat had one wire that didn't have the correct connector on it so I stripped the wire back and used a crimp connector and heat shrink to attach the connector from the failed thermostat. After plugging the new thermostat in I ran the refrigerator for 15 minutes to cool the thermostat and then rotated the defrost timer to the defrost position and tested the new thermostat. Reassembled the freezer compartment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from chrlestown, MA
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
i lost the part and had to replace it
simpley place the support into slot provided.
Was this instruction helpful to you?
Thank you for voting!