ABB2222FES (ABB2222FEx0) Amana Refrigerator - Instructions

You need to lift up the glass part and simply fit it the center rail in, very simple

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!

Plied off the relay switch with a screw driver. I could not pull it off by hand. Disconnected the wires to it and replaced with new part. Had problem getting the part back on and lining up the pins with the connector. I had to line up one pin and start at an angle and roll the part onto the contact pins.
I was impressed with the one day delivery without paying because it was shipped from a warehouse in California where the repair was made.

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed

Unscrewed back of fridge and unplugged relay from compressor and plugged in the new one remember that the new one turns 180 degrees from existing switch.

First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.

Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.

R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin

No instructions came with the parts, however, on the website where we ordered the parts was a video that walked you through every step. We followed the video and had the repair done in no time.

Replaced the electronics board. Fairly easy job. Video helped enormously. Programing is awkward.

Removed back access cover with quarter inch nut driver, unplugged wire harness, pulled old relay out & plugged in new one, reconnected wire harness, and reinstalled access cover. Piece of cake. (Shipping was very quick) ***Frig was only 3yr an 1 mounth old.*** Maytag - Dependable Huh?

While investigating problem (at 11:30PM of course) I saw the overload burst into flames. Problem Identified! Easily found and ordered part. Next day delivery. Exact same part easily plugged in. Total refrigerator down time was less than 40 hrs.

Thanks,
Terry

Once I got the right part the repair was quick and easy. All I had to do is get the old part off with a screwdriver and curved needle nose pliers and the old part came right off. The new part went in just as easy. Quick and easy. Less than 15 minutes.

Repair was a piece of cake. My only wish would have been a little more informed on a few other parts I could have replaced as well. It obviously would have increased my cost, but would have simplified the install process, and still would have been cheaper then calling a service guide. I would recommend buying and installing the new gaskets when doing this. And possibly the steel support bar that goes threw the plastic shelf. Removing that bar was the most difficult task, difficult only that if you used to much force, SNAP!! and then your pissed! and have to start all over.