XRSS687BB (PXRSS687BB0) Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald from Helena, AL
- Parts Used:
- WP67001503
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
slides cracked and broken off in sections
Removed the top glass shelf to make slides easier to reach. Then simply removed the old tray and installed new one. You do have to watch for the small stops in the slides or you could damage new unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Butler, PA
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Bottom Cam broke on Fridge Door
Removed top hinge cover and socketed out hinge nuts. Lifted door off bottom hinge. Socketed out broken bottom cam and replaced with new. Reset door with someone lifting and the other guiding. Reattached top hinge and cover. Voila.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Saint Marys, GA
- Parts Used:
- WP67001503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original drawer slide in component cracked
Pulled out old, slid in new. Presto, change o!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from JACKSON, WY
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
door closure part broken. door wouldn't remained closed
removed door.examined problem,. installed part. super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from LEWISBURG, PA
- Parts Used:
- WP67005959
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
original ice bucket plastic slides onto rack broke and wouldn't support full ice load
On several occasions the ice bucket had fallen inches onto other frozen foods and the auger wouldn't work. After dealing with this several times over a period of several years, I decided to see if I could locate a replacement which I did through your company; We took the old one out, unsnapped parts and then snapped the new bucket to the gate and shazzam, we were able to slide the new bucket into place and it works like new. Hopefully a repair won't be necessary again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Huxley, IA
- Parts Used:
- WP67005959, WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
auger would jam/broke helix end cap
dismanteled ice bucket end and removed auger slid helix off and reinstalled auger in bucket. real good instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Lancaster, SC
- Parts Used:
- WP67002052
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Plastic wheel in icemaker broke
I removed the ice tray from the freeze. Turn over and remove screws holding the face plate on. Remove the 4 screws holding the crushing mechanism in place. Pull the entire mechanism out and remove the nut holding the blades together. Remember the alignment of the blades. Remove blades and then the pastic crush wheel. Replace in reverse order. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oswald from Miami, FL
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice Carrier End Cap
Removed Ice carrier and diassembled the Ice carrier with a socket set. Four screws, cap came right off. Placed the new one on and finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Boise, ID
- Parts Used:
- WP67005959, WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not feed ice out of bucket
I removed the bucket and then took the feed screw out and replaced the end cap and reinstalled the feeder in the new bucket and put it back in place and it worked fine. This is not a hard job, you just have to pay attention to the dismantle so you can get every thing back together properly.
the breakdown and parts list was a big help.
the breakdown and parts list was a big help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eduardo from Natalia, TX
- Parts Used:
- WP67005959
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Cracked on the bottom
With a socket set wrench this is the second time it happen no problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from DUNNELLON, FL
- Parts Used:
- WP12665101, WP12562701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Icemaker chute door seal was deteriorated
Watched a Utube video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Bay City, MI
- Parts Used:
- WP67005959
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The ice bucket had a cracked track
I had to pull the old ice bucket out, remove the front cover and the ice churner from the old bucket. The churner had to be installed onto the new ice bucket, then the front cover had to be snapped back on to the front of the ice bucket. Finally, the new bucket was slid into place. The whole process was relatively easy for a non-mechanical person like me, with the help of detailed instructions that came with the unit. The on-line video was also helpful. I would recommend this company to friends.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from Porter Ranch, CA
- Parts Used:
- WP67001503, 12589104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drawer broke
1. Unwrapped the drawer.
2. Washed the drawer.
3. Placed drawer in refrigerator.
:)
2. Washed the drawer.
3. Placed drawer in refrigerator.
:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROSE MARY from MARYSVILLE, WA
- Parts Used:
- WPW10152975
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Original Armwire Had Fallen Off In The Ice Bin And Got Bent. That Is Why I Ordered The New Armwire Assy.
I removed ice bin and cover that sits ontop of the icemaker. I inserted the longer end of armwire assy first in the front part of the icemaker arm until it clicked in place then inserted the shorter end in the back side of icemaker arm and pressed until it went into the hole all the way through. This was very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from La Mesa, CA
- Parts Used:
- WP67001503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken drawer
Took the old one out. Washed the new one and put it in. The best part was: This company had the part in stock and we received it the next day. Amazingly fast service. Thank you very much.
Was this instruction helpful to you?
Thank you for voting!