ASI2175GRB10 Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Howard from Columbus, OH
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Time to replace water filter
Removed old filter then insert new filter and pushed door closed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Salisbury, MD
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
the drum broke off for the icemaker
replaced the drum ---- however it would of been more helpful if directions came with the part on how to take off the old drum we had to look on line to see how to do that wants we got that done the rest was a piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Shrewsbury, MA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Broken light switch
Pried out the old switch and installed the new switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Lansing, MI
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Plastic chips in ice. Slow to auger to blades.
Remove 4 self tap screws holding on front cover/bin handle. Remove 2 self tap screws holding drum cover. Remove 1 self tap screw at back of bin holding door actuating rod and spring, slide forward to disengage. Remove "E" clip and flat washer. Remove plastic nut {clockwise/left hand threads]and remove crusher parts [keep in order removed]. Slide new drum on shaft and reassemble crusher in reverse order. Install drum cover w/2 self tap screws. Install flat washer and "E" clip. Re install actuator rod and spring assy. Install front cover and test in refrigerator. The 2 self tap screws that hold drum cover are easier to remove with a 1/4' drive ratchet and 1/4" socket because of limited space behind actuator rod. This job is a snap to do. I'm sure it's at least $50.00 cheaper than a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Huntersville, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light hinge broke
Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RALPH from PARAMUS, NJ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator lamp not functioning
Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Topsail Beach, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken refrigerator compartment light switch.
The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Garland, TX
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
ice drum broken
I removed the ice bucket and dumped the ice (saving part of it to put back into the bucket after repair).Using the nut driver,removed all screws,rmoved the auger that the broken drum is mounted on.I reoved the nut on the end of the auger(with my pliers).Slid out auger removed broken drum,replaced new drum and re assembled using your easy to follow instructinns.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Lindenhurst, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
icemaker
installed new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Prague, OK
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
plastic broke so ice would not move to blades
looked at the schematics from online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- catherine from LEEDS, AL
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
ice would not chrush or come out into glass
removed 9 screws, removed all parts, laying them in order, so they would be easy to replace.
reassembled in order I had removed them placing the new auger drum in place of broken one.
replaced ice container in freezer, poured in a few ice cubes them crushed them.
reassembled in order I had removed them placing the new auger drum in place of broken one.
replaced ice container in freezer, poured in a few ice cubes them crushed them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from BROOKLYN, NY
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
noise but no ice would be dispensed
Pulled out the ice tray, took whatever screws held the front on. The rest was pretty easy. The only thing I would say was a problem was taking off the cutters. The front spacer is threaded, and loosens by turning clockwise. Also, the shaft that runs along the side of the tray has a spring and keeper. Make sure yoiu remember how you take it apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fairfield, OH
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
ice was not moving into door crusher
First I removed the 6 screws and then 2 more--being carefull to take cap off inside to nremove metal blades--be sure to keep in order--taking ba digital picture helps at this point--make sure to put back nin reverse order after replacing washer and new auger--went smooth thanks appliance parts repair service forum--Rick--Enjoy your own repair!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- debbie from Shepherdsville, KY
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
would not dispense Ice
Took the Ice Bin Out emptyed it then removed the nesasary screws pulled the broken Peice off and sliped
the new part on held the metal peices together so we would know how to keep them in order for fear of putting them in wrong place but we did it now it works great thank you so much for getting the part to me so quickly your great.
the new part on held the metal peices together so we would know how to keep them in order for fear of putting them in wrong place but we did it now it works great thank you so much for getting the part to me so quickly your great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Fort Mill, SC
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Ice Bin Auger Drum cracked.
It was a breeze to remove and replace. Made even easier by the previous DIY guys posts. Make sure you turn the nut at the end of the shaft clockwise to loosen. Taking a picture of the blades for ice crushing before removal for future reference is a great idea. It wasn't hard at all. Just take your time.
Was this instruction helpful to you?
Thank you for voting!