59679274991 Amana Refrigerator - Instructions

Unscrewed the old handle, cleaned the area, and screwed on the new handle. Simple, and took just a couple of minutes. Our kind of repair!
The handle is now whiter than the rest of the fridge, but (1) were just happy to even find a replacement handle so we could switch it out and (2) no longer worried about it breaking and our having to purchase a new refrigerator just for that reason, when this one is still working just fine. Thank you, PartSelect! (We have referred friends to you :-)

removed the screws and removed the old handle and put the new handle in place and screwed the screws back in.

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

Removed broken handle and replaced with new one by inserting 2 screws. Just took about 2 minutes and is a great improvement!

Unscrew old one replaced with new one

first thing i thought was the condenser was plugged so pulled out and cleaned with shop vacum backwards so it became a blower not a vacum cleaned it good and put together. wife noticed cracking noise inside freezer. took all freezer food and shelfs out. took 1/4 inch hex nut screws out and found complete condenser solid ice. did some research on internet and found parts select stories. i buy passed thermostate and hooked heating coils direct which then thawed condenser. checked timer by turning of and it worked fine until i got part and installed.

The repair went very well. Once the sockethead cap screws were taken out of the seal and the ripped seal was removed, the door panel separated from the door itself allowing me to see that ice had already been forming within the insulation. I was fortunate to have decided to replace the seal when I did or further damage would have occurred. After thoroughly cleaning the refrigerator and freezer I replaced the seal using a hair dryer as suggested to tighten the seal into place. Everything is working as it should once again.

The parts were very easy to replace, however I am still without ice and cannot figure out why. I have ohm tested the contol unit and everything works fine, I am able to jump it and turn on the motor and water fill valve. Any suggestions?...

Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Refer to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!

Loosen bolts, remove gasket. Replace gaskets then tighten bolts.
The gaskets new were very out of shape when they were delivered this made it very difficult to put them back on. Even after warming them up with the hair dryer.

First time refridgerator repair, I was lucky this was not that bad of a job.

Removed food from freezer, took off ice maker by removing three screws, removed back panel by removing six screws. Once the back panel was removed, the fan assembly could be viewed while powered up. It was not spinning and air was not moving above or below the fan. I removed the electrical connections by hand (with the 'fridge powered down) and removed the fan assembly by removing the two screws adhering it to the back of the freezer section. I replaced the fan assembly and had some difficulty because the new unit shipped by partselect had the electrical connections on the opposite side than the original assembly. The wires were barely long enough so I was able to make the connections and subsequently attached everythng in the same manner it was removed and the fridge works great.

Refrigerator door was removed and placed on a set of "horses". Fastners were loosened about 3/4 thread length. Old gasket removed. New one installed. It was necessary to use a "hair dryer" to take out shipping kninks.
Used a piece of 1 1/2 inch sheet styrofoam to seal the door
opening during the process so as not requiring emptying the
unit.

The freezer door was a bit more difficult. This one was done in place. The Styrofoam sheet was cut down and fit in this opening as mentioned above. Inner door panel was removed to reveal heavy ice build up inside door. This was allow to melt and removed along with the fiberglass insulation. New fiberglass insulation was installed and the door reassembled.

In general everything went quite smoothly. Fit on both gaskets was really good.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.