ARB2517CB (PARB2517CB0) Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jon from Boise, ID
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No ice
1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from San Antonio, TX
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Roseville, MI
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken glass on pantry door
Pulled the broken pantry door off, and snapped the new door in place. Vry simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from Cream Ridge, NJ
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
chef drawer cover
take the old one out replace with new once - no instructions required, no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orting, WA
- Parts Used:
- WP10450603
- Difficulty Level:
- Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
broken front wheel
remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Ruth, MI
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My old icemaker lost some of the nonstick surface and the ice didn't want to come out
I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Hanover, MA
- Parts Used:
- WP67006506
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Power cord was cut
I removed the 5/16 inch hex head nuts holding the rear access panel where the power cord was connected. Once removed, I released the Molex plug and ground wire. I connected the new cord, screwed in the ground and installed the rear panel. Having the exact OEM part made the job quick and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Louisville, KY
- Parts Used:
- WP67001036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
freezer was frosting up
Follow your parts diagram, I removed the nut screw from the light in the refrigerator. Removed the light cover. Removed the temperture control knob. Remove the damper control cover. Slid the light assembly forward. Pulled out old defrost timer, replaced with new one. reversed assembly order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linford from Cedarville, NJ
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker would not fill with water.
Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from Piedmont, OK
- Parts Used:
- 12001937
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Back of freezer froze up and not getting cold in refrigertor.
I got on the web blog and saw a conversation on here that sounded just like the problems i have been having with my unit. After reading every thing about it i ordered the part needed and installed it. I let the fridge thaw out over night and started it up the next morning. Its been two month since i installed the part and it is working great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monica from EDMOND, OK
- Parts Used:
- W10823511
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
water leaked when the paddel was pushed
Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David L. from Red Rock, TX
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The orignal proberm was broken hinge on End Cap
There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duncan from Metairie, LA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Switch Broke...Absolutely Fell Apart.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Bronxville, NY
- Parts Used:
- WP67002224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dog ate toe grille
Snapped into place with the attached clips. Could not be easier. Really great service from PartSelect--got here faster than I expected. This was a great service--would recommend to everyone!
Was this instruction helpful to you?
Thank you for voting!