XRSS267BB (PXRSS267RBB1) Amana Refrigerator - Instructions

Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back on and checked the switch. Worked perfectly! Easy job.

Removed top hinge cover and socketed out hinge nuts. Lifted door off bottom hinge. Socketed out broken bottom cam and replaced with new. Reset door with someone lifting and the other guiding. Reattached top hinge and cover. Voila.

Pulled out old, slid in new. Presto, change o!

Removed the top glass shelf to make slides easier to reach. Then simply removed the old tray and installed new one. You do have to watch for the small stops in the slides or you could damage new unit.

Unloaded refrigerator. Pulled refrigerator from wall. Removed bottom panel on back and replaced bolt. Reversed steps but leveled rear wheel before reloading.

On several occasions the ice bucket had fallen inches onto other frozen foods and the auger wouldn't work. After dealing with this several times over a period of several years, I decided to see if I could locate a replacement which I did through your company; We took the old one out, unsnapped parts and then snapped the new bucket to the gate and shazzam, we were able to slide the new bucket into place and it works like new. Hopefully a repair won't be necessary again!

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

I removed the bucket and then took the feed screw out and replaced the end cap and reinstalled the feeder in the new bucket and put it back in place and it worked fine. This is not a hard job, you just have to pay attention to the dismantle so you can get every thing back together properly.
the breakdown and parts list was a big help.

I removed the ice tray from the freeze. Turn over and remove screws holding the face plate on. Remove the 4 screws holding the crushing mechanism in place. Pull the entire mechanism out and remove the nut holding the blades together. Remember the alignment of the blades. Remove blades and then the pastic crush wheel. Replace in reverse order. Very easy.

With a socket set wrench this is the second time it happen no problem

I had to pull the old ice bucket out, remove the front cover and the ice churner from the old bucket. The churner had to be installed onto the new ice bucket, then the front cover had to be snapped back on to the front of the ice bucket. Finally, the new bucket was slid into place. The whole process was relatively easy for a non-mechanical person like me, with the help of detailed instructions that came with the unit. The on-line video was also helpful. I would recommend this company to friends.

dismanteled ice bucket end and removed auger slid helix off and reinstalled auger in bucket. real good instructions.

Popped out the old light switch with a butter knife from the bottom first, disconnected the plug in. Install was just the reverse. Super easy fix

Removed the top hinge cover with Philips screwdriver. Removed the three bolts holding the top hinge in place. Removed the top hinge, and lifted the door off the remains of the lower hinge. Unbolted the remnants of the lower hinge closure mechanism and replaced it with the new set. Reassembled the door on the lower hinge, and then replaced and bolted back on the top hinge. Door back to full working order in less than fifteen minutes.

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!