GT2425PDDW Amana Refrigerator - Instructions

put the end caps on

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

Simply replaced part. Press fit shelf retaining bar back into place. I was just glad you had this obscure part which was easy to find on you website.

The kickplate grille is a plastic part which has two metal clips attached to it. The old plastic frame had broken free of the metal clips and fallen off the refrigerator. Step One: Removed the two old clips by pulling them out of the refrigerator frame. Did it with finger pressure. 2. Pressed the new part which has clips attached to it into the holes in which the old clips had been placed. Voila, the repair was finished.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Just removed old trim and attached new trim by hand. good results. Happy with your product and tmeliness of delivery Thanks Doug Salter

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

After thinking it would be impossible to find the parts I needed to fix my old refrigerator I found PartSelect.com. I was surprised that not only did they carry the parts but all were in stock. The actual repair was as easy as the ordering. For the shelf retainer bars and end caps I just put the ends on the bars and snapped it into the door. Care should be taken not to try to bend the end caps too much to insert into the door or they will break at the inside of the bar. They are only thin plastic. I actually bought two spares for future if needed. For the crisper drawer shelf support I used my 1/4" nut driver and removed the piece of the old support with the screw and installed the new one. Do not over tighten the screw or you might a: strip the hole out the sheet metal screw goes in or b: damage the new support or both.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

The main issue is that my supports are NOT held on by screws -- they are behind the fridge wall and can not be removed. So this is my solution (ignore the 'fix kit' -- it is useless and is just this part plus a metal screw. It cost me $20 to find this out). Here is what I did: 1) Cut off the old support with a knife. 2) Get a small toggle bolt (I used 1/8" x 2", < $2 from Home Depot) and thread into new support. 3) Dig around in insulation to make sure there is space for toggle to flip open. 4) Install!!!! Wish I'd thought of this before :-)

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

I love how easy it was to find out what part I needed by seeing the photos to verified it was the part I needed. The repair was super easy and the directions were easy to understand. I didn't even need tools.

removed old mount with allen wrench replaced with new mount