AFI2538AEW Amana Refrigerator - Instructions

First pull out bucket, then slide side plastic piece that hides wire harness on lower left side out.. Then pull /slide whole unit forward/out. Disconnect wire harness plug when doing so. Set old unit on table standing on end, put new unit right next to it. remove whole tray assembly from old unit, 3 screws on back. Use new wire harness that comes with new ice maker. put new tray assembly on end unit where the other came off. replace the three screws holding it to fan unit. remove on/off switch from old unit and put in new unit cover. Use small screw driver to remove old end switch cover. On off switch is pushed into place on new end cover. Purple wire on bottom plug and other on top. observe what you have and Just replace what you removed. Piece I did not use was flat plastic piece,flapper? This did not come with instructions, so basically I changed everything incl wire harness, put back together and put back in freezer. Ice bucket was full by next morning. Instructions and or video would have been nice. Tool;s used was a 1/4 in nut driver, small flat blade screwdriver.

Parts delivered quick. 15-20 minute repair time. Just needed to remove a few shelves, then screws to remove damaged parts and replace with new. Very easy repair.

Instructions were great five minutes to remove and replace fan....Thank You............ saved big money

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

It was quit simple. I removed the draw and the shelves above the pantry unit. Once everything was removed (2min), I removed the one side pantry bracket ( 2 screw's). Put in the new pantry bracket and screw's and I was done. I'll give it ten minutes total. easy button Thank you

Very simple--Just remove all drawers, remove old end cap, remove slider from old end cap and put on new one. Screw on new end cap and replace drawers. Took about 10 minutes.

First, I took out the glass tray along with the two slide out compartments that are part of that assembly. Then I used a small socket set to take out the three screws that hold the part in place and along with the part a plastic connector comes out with it that adjusts the temp of the bin area. Line up the holes on the slider and two screws come out that hold the slider to the part. Disconnet the plastic piece in the back that adjusts are flow (press down plastic holders) Reattach the slider, snap the plastic piece on the back and reassemble. Sounds complicated but once you are in there, its self explanatory.

Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer. Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.

I broke the glass in the frig and found partselect and ordered the new glass and had it in 2 days. Very fast shipping.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

I initially tested the heating element and defrost thermostat using an ohm meter. the defrost thermostat was incased in ice, so I replaced it first. The refridgerator worked for about a week and then froze up again. I then replaced the thermistor and the unit is working as designed.

It was easier than I had anticipated. Just had to make sure that I was very careful in removing the old part so I did not break any of the good plastic that I needed in order to install the plastic temperature control to the new part.

disconnected the power chord, removed 8" cover at back of refrigerator, disconnected 4 connectors, unclipped the pc board and removed it. replaced the board in reverse order, plugged the power chord back in and performed the coding procedure, which is done with the refrigerator door open, in accordance with the instruction sheet provided. real easy and without the hassel of getting a repair man.