AS2625PEKW Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- kent from fishers, IN
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator door side lower closer cam broke
The worst part was unloading the door shelves. Removed upper hinge cover and hinge hex screws. This allows the door to be removed. Lay the door on side. Remove screw that holds cam in place. Replace
broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover.
Now reload all of the stuff.
broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover.
Now reload all of the stuff.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Duvall, WA
- Parts Used:
- 12580401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
drain hose burned and plugged
replaced drain hose; melted ice that had built up behind it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Smyrna, GA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Frost in bottom freezer, freezer 8%, ice maker works
replaced electric control board, defrost for six hours. next day (24 hours) same problem, [email protected]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Mundelein, IL
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door clicked when opened or closed.
I followed the other web notes with one change .Since I too forgot the lube , I used a pry bar and block of wood to lift the door and a tooth pick to glob some lube in the lower hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Milford, MI
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Plastic Cams on frig door cracked in halk/door wouldn't close easily
Removed the top hinge (4 screws)-lifted the door off of the lower hinge-replaced both halves of the cam kit and mounted the door and reattached the upper hinge.
Probably took about fifteen minutes total.
Probably took about fifteen minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fonce from Ft Lauderdale, FL
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
lower cam broke
Remove the grandkids pictures from the door then empty the contents inside the door. Remove the top hinge cover and the top hinge bracket. Lift the door off the bottom pivot. Replace the lower cam by removing one screw. With the door in the horizontal position, remove and replace the upper cam. Apply a little grease on both cam surfaces. Align the door before tightening the top bracket and your done. If you did not take a picture of the door before you started the project you will have to rely on memory to arrange the pictures in the proper location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Buffalo, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broke plastic tab on auto light switch
Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald T. from Tampa, FL
- Parts Used:
- WP67004028
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost the arm
I have never used the ice maker because I have a well and didn't want to usewell water to make ice. I usually make ice with bottled water.
I decided to try making ice with gravity fed water from a converted water fountain placed on a higher level than the refrigerator, locater in my garage next to the kitchen.
When I looked at the rear of the frig. I saw a copper pipe (on the bottom of the frig.) that lead to a valve, with a plastic tube that went to the freezer. I didn't think that the gravity fed water could go down to the bottom and return to the freezer at the top, so I cut the plastic tube, and fed the water directly to the ice maker.
I only put a small amount of water in my water source because I wasn't shure what would happen. The water filled the tray and the rest of the water went to the container that catches the ice.
I did get one tray of ice. I later found that the valve that the copper pipe went to, has a 7 minute timer that only allows a small amount of water to pass.
My next effort will be to connect to the copper pipe and see if it will allow the gravity fed water to rise to the ice maker. Wish me luck
I decided to try making ice with gravity fed water from a converted water fountain placed on a higher level than the refrigerator, locater in my garage next to the kitchen.
When I looked at the rear of the frig. I saw a copper pipe (on the bottom of the frig.) that lead to a valve, with a plastic tube that went to the freezer. I didn't think that the gravity fed water could go down to the bottom and return to the freezer at the top, so I cut the plastic tube, and fed the water directly to the ice maker.
I only put a small amount of water in my water source because I wasn't shure what would happen. The water filled the tray and the rest of the water went to the container that catches the ice.
I did get one tray of ice. I later found that the valve that the copper pipe went to, has a 7 minute timer that only allows a small amount of water to pass.
My next effort will be to connect to the copper pipe and see if it will allow the gravity fed water to rise to the ice maker. Wish me luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- OLIVIA from BOERNE, TX
- Parts Used:
- 67004268
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
broken chiller door
First I looked at the manual to prevent causing
further damage and read the instructions on how to remove the original parts. I then removed the broken door and attached the new one and replaced it back as directed. Voila!
further damage and read the instructions on how to remove the original parts. I then removed the broken door and attached the new one and replaced it back as directed. Voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WAYNE from KENNERDELL, PA
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch was accidently hit and broke.
plugged the two wires in and snapped the switch into it's socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Davis, CA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch Was Faulty--Failed A Few Months After Purchase Of The Refrigerator
I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Avila Beach, CA
- Parts Used:
- W11291138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken spring in the light switch in refer
Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Duluth, GA
- Parts Used:
- W11291138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
While closing the door, I somehow cracked off the light switch button.
Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Fairfax, VA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Left door light switch lost its spring
Unplugged appliance. Using a small putty knife I moved the switch out far enough to grab it with pliers. Moved wiring to new switch and pushed into place after testing.
Was this instruction helpful to you?
Thank you for voting!