TZ21R2 Amana Refrigerator - Instructions

Repair was as shown in the video except my refrigerator had screws instead of the plastic clips as shown in the video. Just had to loosen the two upper ones and remove the one lower one. All other steps were as shown in the video.

Replaced entire ice maker. Turn off water where it comes out of the wall. Loosen two top screws and remove one screw at bottom. Lift unit up and off top screws and swivel out to the right and disconnect power plug from freezer. Warning new unit does not come with: 1. Power Cable 2. Front plastic cover. 3. Wire bail. Install in reverse order Do NOT toss old unit until new one is installed and working. My came with the bottom mounting bracket bent so I just used the old one. When installing old power cable into new unit be sure to put small sensor into clip. It's part of the cable harness assembly.

Replaced Icemaker

Removed one screw ,unpluged ice maker, and replced it with new one.

First, I removed the ice bucket. Then I removed the two top left screws and bottom screw with a 1/4 inch nutdriver. I pulled the assembly out as far as the wiring harness would allow, disconnected the harness on the lower left side, and removed the unit. I removed the old motor cover and ice stop wire and placed them on the new unit. I then reversed the process. It went so fast that the freezer must have still been close to zero degrees because it filled with water within 15 minutes.

I simply put the post in and set up the drawers and shelf.

very simple,remove old and unplug install new,three screws, used old hose clip.

Barely a couple years old, was not getting any ice. I carefully selected the right part on this website and ordered. Around $150 and was easy install.

1. Mine was upper and lower freezer. you slide the freezer door out and lift it up, it will come right off.
2. pull out the tray above and ice bucket
3. Use a screwdriver to unscrew 2 screws above and one below the existing icemaker
4. unclip the power cable line

Thats it!

Point to note: the new piece you get will not have the power cable line, the water cover and the metal arm. I would think it should have for $150, but keep this as you will need a few little parts to complete the new part before installing it back.

VERY easy to do installation. Dont pay anyone to do this, it can be done easy!

It was real easy. I unpluged the fridge. Took out the three screws that held the icemaker to the wall. Unpluged the wire harness. Removed the old icemaker and reversed the order to install the new one. Everything lined up perfectly.

First I couldn't get it back..due to eye problems so i gave it to my husband and he just did it in a flash..you set it under the glass and put the drawers or crispers back in and its done.

Removed two screws on top. Then one under the ice maker ,held on to it while I unpluged the white flat plug. Then installed new one in reverse. Of course re-connect power wires on.
I turned power off at fuse box.
First batch of ice in an hour or so.

I removed three screws each on the old handles & removed the handles.
I reversed the process by attaching the new handles using the old screws.
All looks great.

First i removed the top two screws that help the ice maker in place then remove the bottom screw, then unplug unit from freezer, removed ice maker for freezer, took out wire harnes, put wire harnes in new ice maker, plug new unit in place the unit in freezer and put in the bottom screw, them align the top two screw and but them in and was done. Check ice maker in two hours and there was new ice being made.

I took the screws out holding old old ice maker, unpluged the electrical socket and old unit came right out. All I had to do then was plug electrical socket into new icemaker place unit in position and put the one screw back in the held it in place. Plug frig and and it filled with water in about 15 minutes and started making ice. Part was a exact match to the one I removed.

very easy, 3 screws,took old one out, take 2 inter screws out (of ice maker) of old unit to replace water feed cup on new unit very easy,installed had ice after 12 hrs.