36588-P1108402W Amana Refrigerator - Instructions

I removed the screws on the back of the refrigerator revealing the water valve, disconnected the water supply, removed the two outlet hoses and removed the bad valve. Replaced in the opposite manner.

I made use of instructions for other users, see 'My ice maker has been shedding.....' and they were very helpful. The one problem not covered - the instructions that came with the new icemaker said to 'remove the bearing and inlet from the old icemaker and install in the new icemaker', but gave no instructions for how to accomplish this.

The old inlet has a square opening in the back and a u-shaped knockout in the side. The new one has a round opening in the side and square knockout in the back)

After several attempts to remove them, I gave up and used the new inlet with the knockout removed. I did not attempt to cover the side opening and it worked fine that way - no leaks.

Replaced ice ice maker using
All of the instructions on the website.
Very easy. A couple of the screws I had
To feel for because I couldn't gety big head
In the freezer far enough to see them.
Very simple and only took about 15 minutes.

Removed the old icemaker and installed the new one. The first one we ordered lasted about 4 weeks and pooped out. Parts Select was very nice and gracefully sent another in two days time. This one has been installed and is working fine...Hope it stays that way.

Thanks...Ron Norwood

This was a very easy repair. Of course start by unplugging the power cord. Take out the lower freezer drawer. Unplug the wiring harness from the ice maker at the rear of the freezer. Undo 3 screws with a 1/4" nut driver. The ice maker will come right out. You don't have to undo any water connections, the feed tube just slides into a guide in the ice maker. Once the ice maker is out, unplug the harness from the old one and snap it into the new one. Same with the cover. Reassemble in reserse order. Plug the power cord back in and wait a couple of hours for the familiar sounds of ice cubes falling into the tray.

Removed covers. Lifted and angled out the freezer unit. Removed clips at bottom and pulled out the heater coil. Threaded the new coil in place and replaced the clips. Lifted and hung freezer unit back in place. Re-connected wires and turned on the fridge. Verified that fan worked when cooled down and defrosted at end of cycle. Replaced the covers.

Replaced ice maker but now water valve wont work

There are basically three screws that hold the unit in place on the inside of the freezer. Removing them is relatively easy, and the unit is replaced with the same three screws. You do have to use the formed metal wire from your old unit, so don't throw it out! You also have to use the wiring harness from your old unit.

Ice maker assembly required disconnection of the wire harness at the back of the freezer and the removal of 3 hex nuts. The assembly did not come with a new wire harness nor the rigid wire attached to the hinge that can be raised to stop production of ice. The wire harness was easy to disconnect from the old assembly by pressing in on a tab. The rigid wire attached to the hinge simply required pulling straight out of the hinge-hole (no need to twist, slide, or perform other contortions...it does require significant force to remove, but it does pull straight out). It was simple to attach it to the new ice assembly. Reinstalled the 3 hex nuts and wire harness plug and was good to go....after waiting several hours! I was worried at first because the unit did not immediately fill with water after I plugged the fridge back into the wall socket. However, after the freezer was cold enough, the water did run and I had my first ice dump within about 3 hours of finishing the installation. We have good ice again, and Partselect has excellent pricing and awesome delivery! I received the unit the day after ordering, and I had only paid the basic shipping! Thanks Partselect! Jeff

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

Moved frig away from wall, unpluged and took off lower back panel. Disconnected water line and ice maker lines from water valve (after shutting water off). Removed 2 screws, New valve was exact replacement. With new valve in hand, I removed electrical connecters one at a time and placed them on new valve. Put new valve in place, inserted 2 screws and tightened, Connected water lines, checked for leaks, moved frig back in place, job complete. No more drips, worked perfect. Total time, about 30 min.

1. Moved the firdge out so I had room to get bhind it.
2. Un-plugged the fridge so I didn't get electrocuted.
3. disconnected the the water hose from the broken water inlet with adjustable wrench.
4. Put hose in bucket to drain and moped up water from inlet valve with towel.
5. removed the 2 scrwes with socket driver that holds inlet on fridge.
6. reached in behind the inlet valve and unplugged the wires from the inlet valve (total of 2 plugs)
7. pulled the inlet valve out of the back of the fridge.
8. removed the bolt that holds the ground wire the metal plate that the inlet valve was connected to.
9. removed the defective inlet valve from the metl plate and tossed the defect valves.
10. put the metal plate on the new inlet valve.
11. screwed on the ground wire to the metal plate from new valve.
12. plugged in the 2 plugs back onto there proper locations on the inlet valve.
13. put the assembly back into place in the back of the fridge and screwed in the remaining 2 screws to hold it in place.
14. Put plumbers tape around outside of inlet to reduce leaks.
15. re-attached the hose and tightened it with the wrench.
16. turned on the water from the wall and verified there were no leaks.
17. Plugged in the fridge and tested that the water on the door worked.
18. Pushed the fridge back into place and the kids could once again enjoy water from the door of the fridge and in about 5 hours we had some ice again for our drinks.