GT1927PDCW Amana Refrigerator - Instructions

Took both left(broken one) and right brackets off. They come out opposite what you may think. You must pull down on them and then out. Previous post alerted me to pull down, and he was right. Pliers helped give me leverage.

I put the shelves into bracket on both sides before inserting them back into position. Popped right in with a firm push.

All's well that ends well.

Broken for over 5 years!!! lost power in a storm freezer empty got model # went to google found partselect very easy to order. Parts came in less than 2 days, popped one in on each side very easy!!! very very happy!

Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.

Good news/Bad news story. One of your parts view showed the side rails without the drawer rollers another showed the rails with rollers. I ordered the rails expecting that they would come with the rollers attached. They did not so I had to place a second order for two rollers and two screws. As I live in CA, delivery was just a day for first order, but for second I ordered on Sat, delivery was on Tuesday. My complaint was double shipping and handling so total was almost $50.for two very simple items.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

took off lower bracket, replaced parts, put back together, no more squeek!

Removed screw holding the broken support then using the same screw installed new support. Easy job.

Removed the Crisper drawers and shelf. I then used a nutdriver to remove the broken supports, and installed the new supports using the same screws.

snapped on new kickplate

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

My husband did it in less than two minutes. He removed the old part using a small screwdriver and simply inserted the new part. It was the easiest, quickest repair we ever did! PS The part arrived only a couple of days after ordering it. The service was wonderful!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.