HMG601040 Admiral Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jane from Albuquerque, NM
- Parts Used:
- 70197-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken door shelf retainer
removed broken retainer with pliers and inserted new part. It was extremely easy---and I have ZERO mechanical skills.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GROVESPRING, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
light did not work on the refrigerator side
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David Barnes from ROSWELL, NM
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rocker on switch broke off
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neill from Albuquerque, NM
- Parts Used:
- WP70111-108
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Retainer bar was missing.
I had to cut the bar to the right length with a hacksaw. The most difficult part was getting on the plastic supports/pins on either end. I'm not sure a hacksaw is the best way to cut a retainer bar, but it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from TEMECULA, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light switch broke off
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnnie from Saginaw, MI
- Parts Used:
- WP61001846
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
unit would not freeze
I removed all covers then removed screws from element and disconnected wires and removed it.
when installing the new heater I payed close attention to the routing of thw wires to insure that the terminals were connected properly. I then replaced all covers and turned the frig on and in a couple of hour it was working great again
when installing the new heater I payed close attention to the routing of thw wires to insure that the terminals were connected properly. I then replaced all covers and turned the frig on and in a couple of hour it was working great again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from LaPorte, IN
- Parts Used:
- 12001414
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Water leak in Ice making area
I took Ice maker off and found that water was continuously dripping from water line in to icemaker, I replaced valve and that solved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bel Air, MD
- Parts Used:
- WP61004888
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
motor wore out making loud noise
unplug the refrigator, remove everything from
frezer compartment. remove ice maker three screws and un plug. remove rear panel 4 screws
remove motor bracket from rear panel 4 screws
unplug motor . replace motor and reasemble in
reverse order. the new motor is very quiet.
frezer compartment. remove ice maker three screws and un plug. remove rear panel 4 screws
remove motor bracket from rear panel 4 screws
unplug motor . replace motor and reasemble in
reverse order. the new motor is very quiet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Kalamazoo, MI
- Parts Used:
- WP61001846
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer and Frig was not cooling down. The freezer side was all froze up on the coils.
Unplug the Frig and left the freezer side total defrost. Mine was so frozen up, it took about 6 hours with the door open. I had a towel in the botton to catch all the water and ice that fell.
Removed all the shelving units. There are 3 screws that hold the ice maker in place. Loosen the 2 screws above the ice maker about 3 or so turns. Then remove the screw under the ice maker completely. Then lift the ice maker off of the 2 screws that you just loosened. Then with a small flat blade screwdriver, push the plastic clip that holds the connector of wires that plug into the ice maker.
Then remove the screws that hold the back plastic cover that conseals the coil.
Now you should see the coils. There is one heater unit in the middle and one at the botton. There is a screw on each side of the heater unit that you need to take out. They are screwed into a metal bracket that is part of the coil system. Once the screws are removed, you simply remove the heater units. They are plugged in at the top of the coil system on a circuit board. Unplug them from there, (one of the spades connector was slightly bigger then the other, so I new where to plug them back in). Fish all the wire and heater untis out and you are ready to re-oinstall the new units.
Getting the wires back up through the coils was tricky, but I was able to do it.
The hardest thing was working inside the freezer unit. It is not very wide and was sometimes hard to get both hand inside to work.
Removed all the shelving units. There are 3 screws that hold the ice maker in place. Loosen the 2 screws above the ice maker about 3 or so turns. Then remove the screw under the ice maker completely. Then lift the ice maker off of the 2 screws that you just loosened. Then with a small flat blade screwdriver, push the plastic clip that holds the connector of wires that plug into the ice maker.
Then remove the screws that hold the back plastic cover that conseals the coil.
Now you should see the coils. There is one heater unit in the middle and one at the botton. There is a screw on each side of the heater unit that you need to take out. They are screwed into a metal bracket that is part of the coil system. Once the screws are removed, you simply remove the heater units. They are plugged in at the top of the coil system on a circuit board. Unplug them from there, (one of the spades connector was slightly bigger then the other, so I new where to plug them back in). Fish all the wire and heater untis out and you are ready to re-oinstall the new units.
Getting the wires back up through the coils was tricky, but I was able to do it.
The hardest thing was working inside the freezer unit. It is not very wide and was sometimes hard to get both hand inside to work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francis from longmont, CO
- Parts Used:
- 70197-1, WP70111-108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
missing door shelf retainer
ordered new retained and fastners
cut to length per instructions
installed
repair completed
thanks for your service all parts were correct and deliver on time
wayne winkler
cut to length per instructions
installed
repair completed
thanks for your service all parts were correct and deliver on time
wayne winkler
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gaylon from Auburndale, FL
- Parts Used:
- WP60100-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
missing clips
I had to find a couple screws that would match the clips and kickplate. I screwed on the clips. The kickplate snapped on perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Byron Center, MI
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light in my refrigerator didn't work.
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STANLEY from OAKLAND, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rocker switch broke off
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Watertown, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
19 year old light switch broke
Great service. Unpluged old switch and pluged in new one. Works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Jenkintown, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lights didn't always come on when was opened
Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!