19284A Admiral Refrigerator - Instructions

First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!

Service and shipping were fantastic! I would definitely use Partselect again!

First, I read the instructions that came with the replacement ice maker, which I found confusing because they were apparently written to be installed in some other make of refrigerator. However, after removing the white plastic cover on the new unit and insuring that it was identical to the one that came with the refrigerator, I removed the old unit by first, removing the bottom screw that held the unit to the side of the refrigerator. Then, I loosened the two top mounting screws. slid the unit up and pulled out and away from the side of the refrigerator. Then, holding the unit in my left hand, I pinched the two plastic tongs on either side of the wiring harness where it attached to the outlet at the back of the refrigerator, took the ice maker out of the freezer compartment and set it aside. Then I located the water regulator screw on the right side of the new ice maker and turned it one complete turn clockwise to reduce the amount of water that would fill the unit. After reinstalling the white plastic cover on the new ice maker, I saw that the wiring harness that came with it would not fit my refrigerator's outlet. So I removed the wiring harness from the old ice maker and installed it on the new one. Then I connected it to the outlet at the back of the refrigerator, slid the ice maker over the two top mounting screws and then pulled down to seat the screws. Next, I used a small torpedo level to level the ice maker both vertically and horizontally. This required placing several flat washers behind the metal mounting bracket at the bottom of the ice maker and the refrigerator wall. Once I had leveled the new ice maker, I tightened all three screws and shut replaced the ice receiver tray. Works fine.

r#1 removed upper hinge bracket, removed icebox door, unscrewed middle hinge bracket, removed main door, extracted broken plastic bushings, pushed in new bushings, reversed process while adjusting doors. works fine now.

#2 compared door seal with new one from partselect. Turned out that new seal is not magnetic. Had to return. Door still has bad seal.

I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

First pull out frig and unplug. Shut off water valve. I just had to remove two screws to disconnect unit from bottom rear corner of frig. Pull element out just a few inches and disconnect the plug that feeds it electric. Disconnect water hose and reattach to new unit. Reconnect electric plug and reinstall in back of frig, securing with two screws. I have an older appliance, so I had to jury rig a bit when reattaching new unit by drilling two new holes for mounting. Also, I had to buy a new water hose because the old part would not accept the standard female end of the hose to connect to. Home Depot has the standard icemaker hoses with two female ends. These two glitches would probably not apply to a newer appliance, but anyway, it's cranking out the ice just fine now! Sure I saved alot of money, even with the extra $10 investment for the hose.

Most importantly make sure you get the wrinkles out of the gasket, a step we did not follow exactly, so we ended up having to work the seal a lot more to make it fit properly which of course made the repair take longer than needed. Other than that no problems here

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Due to some deformity of the gasket, it didn't seal all the way around. The instructions suggested using a heat light to warm the gasket with the door open. That didn't work too well so I closed the door and used a heat gun lightly in the areas it didn't seal. That worked great to soften the gasket so the magnet in the gasket could pull it gasket tight to the refrigerator. I let it cool with the door closed and it now seals perfectly.

Ice make was still working but no water coming in to make ice . Pulled refrigerator back and found water valve at bottom of refrig close to the floor. I disconnected water line and electric plug - went to whirlpool web site - no help at all to confusing - found partselect and compaired picture of old valve with picture of new valve . When I got it in mail it took 30 min to install - working fine now hint - mark top of electric plug so you install correctly

Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.

order a new try and install

Removed old valve first, found part # on it.
Entered part # into search box on computer.
It came up with the right replacement part the first time!!!
Ordered part, it came in sooner than I thought it would.
I attached the supply line, pushed in the plastic outlet hose, connected the power line, and attached it to the refrigerator frame. We had a full container of ice the next morning.It couldn't of had been easier.

I used this part on a little, under-counter U-line ice maker that is the best little ice maker in the world. The single solenoid part from U-line cost more than twice as much as the generic GE one I ordered from you. It arrived in only 2 days and I was able to just remove the inlet and outlet line from the old solenoid and unscrew the bracket to remove it. I used the included bracket and one screw affix the new one to the ice maker, then just pushed on the inlet and outlet lines, tightened them on, plugged it back in and In about 20 minutes from start to finish, it was back in business, cranking out ice really quick as it was before. Could not imagine summertime in Texas without my U-line,,,Thank you!!!

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.