19902-0A Admiral Refrigerator - Instructions

I read the previous repair story and agree with the author that the screw behind the front piece was difficult to remove and re-install. If I had a magnetized nut driver I think it would have been easier. There were no installation instructions so I relied upon the repair experiences. The other two screws came out easily and I found the harness release easily and the harness was easy to reinstall.
I am not a good handyman but was able to install the new ice maker

installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.

Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.

Unplug wire harness back of fridge. Unscrewed 4 screws on guide for ice bin. then unscrewed two screws holding ice maker to wall of fridge. removed ice maker. then had to take front cover off (pull hard, it comes off) and remove wire harness plug from the ice maker. save this, front cover, and all hardware to re-use. reverse steps to reinstall, including wire guide that goes up and down to stop and start ice maker when bin fills. Have to put this into front part of ice maker correctly for it to work. make sure it is down so that it will produce ice. ice tray took a few hours to fill with water initially, must be on a timer or something.

to easy to describe, remove 3 screws and a wire plug then install new unite.
Works great
Thanks

As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.

There are basically three screws that hold the unit in place on the inside of the freezer. Removing them is relatively easy, and the unit is replaced with the same three screws. You do have to use the formed metal wire from your old unit, so don't throw it out! You also have to use the wiring harness from your old unit.

Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

remove 3 screws,rotate assembly,depress lock on wire harnass connector,un plug harnass.remove old assembly,remove and transfer side cover and steel wire at front of assembly,connect harnass to new assembly,rotate into place,aling screw holes and install 3 screws.flip front steel wire down and wait for about 1 hour,first tray of ice will fall..all done.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness

Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on

ALL FIXED!

Very simple fix, remove 3 screws, two connectors to the old switch

Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.

I made use of instructions for other users, see 'My ice maker has been shedding.....' and they were very helpful. The one problem not covered - the instructions that came with the new icemaker said to 'remove the bearing and inlet from the old icemaker and install in the new icemaker', but gave no instructions for how to accomplish this.

The old inlet has a square opening in the back and a u-shaped knockout in the side. The new one has a round opening in the side and square knockout in the back)

After several attempts to remove them, I gave up and used the new inlet with the knockout removed. I did not attempt to cover the side opening and it worked fine that way - no leaks.