ICNT22F93A (5B78B) Admiral Refrigerator - Instructions

I had to find a couple screws that would match the clips and kickplate. I screwed on the clips. The kickplate snapped on perfectly.

Remove the 3 screws and disconect the plug. The wiring harnes on the new Ice Make did not match so I use the wiring harness from my old unit. I pluged the new one in and screwed in the three screws and it was ready. I did have to wait a full 24 hours before the first 8 pieces of ice eject out.

removed all three screws, disconnected power. then I switched out the plug assembly (mine had different male adapter. Then the Control Arm, new arm was to wide and took up to much space when it was fully extended. Put it back in reverse order, and within 5 hours it was making ice.

I read what other people had done so I tried the easiest solution--Forced, without breaking, the plastic & fit the ring right where it needed to be.

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

To replace the broken drive coupling on the motor end of the auger requires sliding the ice bin out of the freezer section of the refrigerator. Remove the ice cubes and let it thaw out for a few minutes. Remove five screws holding the front face on the ice bin to remove the ice auger. slip the new drive coupling over the end of the auger. reassemble and replace the face plate with the five screws. Slide the ice bin back in the freezer. Less than fifteen minutes it was finished.

It was simple to just replace the shelf support. This is the thrid time I have used Parts Select for replacment parts. They always have the parts in stock, ship really quickly and it's a beeze to search their site for the parts I needed every time. Parts Select is now at the top of my Favorites list when it comes to appliance repair needs. Thanks to everyone at Parts Select!

Checked the ice tray and could only find the drive ring had some breaks in the plastic. Actually did not see why this would stop the auger from turning and dispensing ice. However this was the only thing I could find wrong with the unit. I pulled the tray, removed 6 screws (star tip heads) pulled the auger forward and replaced the drive wheel, put the unit back together and its been working fine ever since.

Easy disassemble removing screws to separate front of ice bin.Be sure to note how metal rod is attached to rear of ice bin. Installed drive ring and reattached face (front) of ice bin in about 15 minutes.

Unscrewed the right control knob. Removed the left temperature control knob (there is no screw holding it), removed one screw to rear of small panel then pried open from the rear of the small panel, there are two plastic tabs in front of the small panel holding it in place. Unscrewed the failed control unit and replaced it with the new one. Replaced the small panel and screw then the left side control knob, making sure of the alignment in the "off" position as the knob has to be pressured into a clamp arrangement on the cold control thermostat. Re-screwed the right knob into place, as well.

removed torx screws and replaced ice bin drive ring.

Easy repair - Don't over complicate it. 1) Flip up ice bar to stop making new ice. 2) Pull out the complete ice bin/tray. 3) shut freezer door while you work on the ice bin. 4) All you need to do is remove the 4 screws holding the ice bin holding tray to the front of the Ice cutting section in the front. 5) Screw drive can then be pulled forward to remove the old/broken white drive cap. Just replace the White Drive ring, put the drive screw back into the ice bin tray and re-install the 4 screws. 6) When re-inserting the bin, you may have to twist the screw drive slightly to re-align with the motor bracket in the back of the freezer. Suggestion: throw out old ice because if it is wet or slightly melted, when you put it back in the freezer the ice will freeze/clump together into a large ice clump; not cubes. Also dry out the ice bin so there is no water to freeze up or create a new jam when the ice bin now re-freezes.

I pulled the dispenser bin and emptied the existing ice (the maker worked, the dispenser would not dispense). Though there appears to be more, there are about 4 (reciting from memory)very small tap screws holding the front of the dispenser unit to the bin. The dispenser activation screw mounts over protruding items at each end. The item at the back (away from the dispenser gear package) is the drive ring that was broken. The drive ring is a small plastic cup that inserts into an opening at the back of the bin (female side to the rear) and slides into the distal end of the activation screw on the same end. One must line up the small slot on the inside of the drive ring with the end of the screw. Slide the assembly together (make sure that the cube/crush switch rod is properly clipped in place with the return spring hooked to the clip), GENTLY install the 4 or so screws and return he assembly to the freezer. It should work flawlessly. Elapsed time: 15 - 20 minutes.

Problem caused by ice cubes falling out of ice bin and collecting at rear and interfering with ice dispenser drive. Broke plactic drive ring. Pull down 2 clips at front bottom of ice bin. Pull ice bin out. Dump ice cubes. Remove 8 star drive screws to allow case to move far enough to clear broken drive ring. Replace drive ring. Reinstall and tighten 8 screws. Install ice bin. Correct loose right side ice cube retainer board to prevent cubes from falling out of ice bin.