GS20C6C3EV Admiral Refrigerator - Instructions

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

placed the retains on door shelf and snapped on. the only problem I had was finding the retainers, thanks to you guys you had the parts that I needed. Plus with your web site it made my search easy. Thanks

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

had it done by my husband, I did not do it

To replace the broken drive coupling on the motor end of the auger requires sliding the ice bin out of the freezer section of the refrigerator. Remove the ice cubes and let it thaw out for a few minutes. Remove five screws holding the front face on the ice bin to remove the ice auger. slip the new drive coupling over the end of the auger. reassemble and replace the face plate with the five screws. Slide the ice bin back in the freezer. Less than fifteen minutes it was finished.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.

Problem caused by ice cubes falling out of ice bin and collecting at rear and interfering with ice dispenser drive. Broke plactic drive ring. Pull down 2 clips at front bottom of ice bin. Pull ice bin out. Dump ice cubes. Remove 8 star drive screws to allow case to move far enough to clear broken drive ring. Replace drive ring. Reinstall and tighten 8 screws. Install ice bin. Correct loose right side ice cube retainer board to prevent cubes from falling out of ice bin.

Easy repair - Don't over complicate it. 1) Flip up ice bar to stop making new ice. 2) Pull out the complete ice bin/tray. 3) shut freezer door while you work on the ice bin. 4) All you need to do is remove the 4 screws holding the ice bin holding tray to the front of the Ice cutting section in the front. 5) Screw drive can then be pulled forward to remove the old/broken white drive cap. Just replace the White Drive ring, put the drive screw back into the ice bin tray and re-install the 4 screws. 6) When re-inserting the bin, you may have to twist the screw drive slightly to re-align with the motor bracket in the back of the freezer. Suggestion: throw out old ice because if it is wet or slightly melted, when you put it back in the freezer the ice will freeze/clump together into a large ice clump; not cubes. Also dry out the ice bin so there is no water to freeze up or create a new jam when the ice bin now re-freezes.

I pulled the dispenser bin and emptied the existing ice (the maker worked, the dispenser would not dispense). Though there appears to be more, there are about 4 (reciting from memory)very small tap screws holding the front of the dispenser unit to the bin. The dispenser activation screw mounts over protruding items at each end. The item at the back (away from the dispenser gear package) is the drive ring that was broken. The drive ring is a small plastic cup that inserts into an opening at the back of the bin (female side to the rear) and slides into the distal end of the activation screw on the same end. One must line up the small slot on the inside of the drive ring with the end of the screw. Slide the assembly together (make sure that the cube/crush switch rod is properly clipped in place with the return spring hooked to the clip), GENTLY install the 4 or so screws and return he assembly to the freezer. It should work flawlessly. Elapsed time: 15 - 20 minutes.

ordered the parts. The bar took awhile to come in. The bar was too long for the fridge, so I had to hack of the end of it, then slid it into the two retainers I had put into the fridge.