GT15A6XV Admiral Refrigerator - Instructions

Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.

I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

This was very easy and pretty fast to do and its working great...all for $40 bucks ! you can do this...trust me!

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

This was a very easy fix. I took the old ice maker out, including the electrical harness. Switched the harness and stop bar to the new ice maker on my bench, then installed the new assembly. Ice initially had some hollow cubes. I checked the ice maker for level. But it was fine. Thought it might be moving too fast. But it seems to have cleared up. Perhaps it took some time to completely cool down.

Replaced entire ice maker. Turn off water where it comes out of the wall. Loosen two top screws and remove one screw at bottom. Lift unit up and off top screws and swivel out to the right and disconnect power plug from freezer. Warning new unit does not come with: 1. Power Cable 2. Front plastic cover. 3. Wire bail. Install in reverse order Do NOT toss old unit until new one is installed and working. My came with the bottom mounting bracket bent so I just used the old one. When installing old power cable into new unit be sure to put small sensor into clip. It's part of the cable harness assembly.

Repair was as shown in the video except my refrigerator had screws instead of the plastic clips as shown in the video. Just had to loosen the two upper ones and remove the one lower one. All other steps were as shown in the video.

Tuned up the ends of the bracket with a needle-nosed pliers then installed new retainer clips into bracket. I then laid on floor and lined up two holes in door and bracket (one end at a time) and pushed retainer clips into door's existing holes. Door was open for less than 30 seconds. Bracket is now solid and holding. Note: Do not jam products in bottom or any shelf thus putting pressure on bracket. Find a new home for the product!!

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Easy to replace refrigerator bar retaining clip. Just pop it off with flat tip screwdriver, put the new clip in the bar, slide bar in place till the studs on the clip line up with the holes in the door and pop the clip in place.

I disconnected power, turned off water supply, removed three hexhead screws, disconnected wiring harness plug, then reversed procedure. New icemaker seens to be a little slower in making cubes. However, the cubes are clean, perfect shape and THEY DO NOT CONTAIN ANY OF THE BLACK COATING AS THE OLD ICE MAKER CAUSED. THIS WAS A FAIRLY SIMPLE TASK.

Removed old ejector arm and installed new part.

Replaced Icemaker