PNS24H9A Admiral Refrigerator - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

removed part., got number, went online,found part, ordered part, paid for part, replaced part.
works great. !

Removed power, removed the ice maker being held with three screws. Replaced with old unit. This box was so old that I robbed parts from the old and placed them on the new unit. Mkes ice very good.

After trying to clean and use chemicles to remove residue, I found that it would not work. Ice would build up in tray causing an overflow in the fill process. this would freeze cubes in tray below causing dispenser not to work properly, New tray seemed to solve the problem. Removed old and installed new

Just took old ice tray out and put new one right in place in less than 30 seconds. I am very pleased with how fast the tray arrived after being ordered. if only everything ordered could be made this simple. You are a great company to deal with.

replacement was relative easy. The problem came with wire connector that had to be cut, stripped and crimped. The crimping was the dificult part. the connector was a problem to crimp.

Very slowly, had no clue what I was doing. Instructions were great, and even I got the job done.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

I pulled the drive ring off of the icemaker and replaced it with the new part. Saved a $150 service call plus cost of part. It cost me a little over $11.00 and a repairman probably would have charged $30.

Turn off refrig water supply, remove cardboard rear lower cover, disconnect two plastic lines (one for icemaker, the other for in-the-door water dispenser) and one copper fitting (supply line). Replace valve (mounted with one screw), reconnect, test for leaks.

The valve I was so sure was bad wasn't, replacing it didn't solve my problem. Turned out to be a frozen up icermaker water feed tube at the top rear of the refrig. The Fix: heat a metal rod of appropriate size in boiling water or with a hair dryer, poke it gently up into the water drop tube (sticks out just above the rear of the icemaker) from the inside and melt out the ice plug. Be sure to test this tube if you have the same problem, you should be able to disconnect the line on back of the refrig and blow air through the tube if it's clear. Saved the valve anyway for a spare.

I tilted the unit back enough to scew the new legs into the threaded holes.

Removed 6 screws to get at broken part. Had to remember the disassembly sequence to properly reassemble. The whole process was relatively simple. I saved about $125 which would have been the cost of a repairman coming to the house.

I removed the 2 crisper drawers and the glass shelf directly above the Pantry Drawer. Removed the Pantry Drawer and Pantry Drawer cover so you have easy access to the Right-Hand End Cap. On the right-hand End Cap, there are 2 screws which hold the End Cap in place, use a 1/4 inch driver to unscrew the screws from the front of the cabinet on the End Cap and half-way in of the cabinet, leave the screws in their holes in the End Cap. Lift gently to get off a small plastic pin, and move the End Cap away from the Cabinet. You don't need to completely pull the End Cap out of the cabinet, it'll move more like a door opening. Place 2 washers on each screw and gently put the End Cap back into place, being careful NOT to jostle too much so the washers don't fall off the screws. You will need to gently lift the End Cap back in to place over the plastic pin. Hand-tighten the screws back into place with the 1/4 in driver. Remount the Pantry Drawer on the sliders. When you go to install the Pantry Drawer Cover, you will need to gently push on one of the pins to get the cover back into place. Put glass and crisper drawers back into place.

Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.

Took out the old drawer and slid the new one

Removed the screws that held the main ice bin and slid back the bin to leave space behind the auger to remove the broken ring. Replaced with new ring and replaced screws to hold ice bin back in place.