DNS22F9A 5L46B Admiral Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Don from Frankfort, KY
- Parts Used:
- W11117769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Renters removed leveling legs from refrigerator. I don't know why!
I tilted the unit back enough to scew the new legs into the threaded holes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- José from Hialeah, FL
- Parts Used:
- 61001451
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The drawer had cracked from use
Took out the old drawer and slid the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from St.Johns, FL
- Parts Used:
- WPW10189190
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Compressor would not start and run, kept making a clicking noise.
First I unplugged the refrigerator, then removed the lower back panel to get access to the compressor. Then I removed the original compressor start relay, removing the metal clip and unplugged it from the side of the compressor. Installed the new compressor start relay from partselect. Plugged the appliance back in and the refrigerator started working again immediately with the compressor running properly and no more clicking sound. Reinstalled lower back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boyd from North Fork, CA
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice bin drive ring broke
Removed the screws that held the main ice bin and slid back the bin to leave space behind the auger to remove the broken ring. Replaced with new ring and replaced screws to hold ice bin back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Lowell, MI
- Parts Used:
- 833697
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
original motor stopped
removed old and instaslled new. biggest problem was getting to one of the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from COVINGTON, LA
- Parts Used:
- 833697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrigerator stopped cooling due to condenser over-heating
Pull refrigerator out to access back, unplug unit and remove the 3 .25" screws cut the power leads to motor and install new with easy to understand instructions provided with new motor. Plug refrigerator back in and enjoy your cold beverages once more. EASIEST REPAIR EVER.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Claymont, DE
- Parts Used:
- WP59688-1A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the ice was sticking to the tray and would fill each time it cycled the flood the dispencer
replaced the ice cube tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from ponchatoula, LA
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no ice in bucket
looked a website removed part found broken item order and installed in 15 minutes, easy simple fix very low cost change
rl
rl
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from Parrottsville, TN
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Metal Augar Damaged End On Plastic Ring I
Removed drive assembly end of ice bin using socket wrench to get to old ice bin drive ring. Pull drive sssembly back to get ice bin ring out of the other end of ice bin. Installed new ice bin ring and and reinstall drive assembly end.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Milford, MA
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
freezer and food section too warm
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Belhaven, NC
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
cooling fan quit
Ordered new fan motor on line took out old motor and replaced with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from whitwell, TN
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
fan motor had gone bad
I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from LaPorte, IN
- Parts Used:
- 12001414
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Water leak in Ice making area
I took Ice maker off and found that water was continuously dripping from water line in to icemaker, I replaced valve and that solved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Tonka Bay, MN
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Condenser Fan Failure
Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Sedona, AZ
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Motor noise while running and clicking when shutting off
The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.
Was this instruction helpful to you?
Thank you for voting!