HMG23822-7A Admiral Refrigerator - Instructions

I had to find a couple screws that would match the clips and kickplate. I screwed on the clips. The kickplate snapped on perfectly.

First I loosened 2 phillips head screws at the top of the ice maker (the one that is close to the front is a little difficult to get a screwdriver on). These 2 screws do not have to be removed. Took 1 screw out of the L-bracket at the bottom of the ice maker. I then slipped the icemaker upward from the 2 top screws and unplugged the electrical wires at the connector at back of the refrigerator to remove the ice maker. I then removed the front cover from it and placed it on the replacement ice maker. I also swapped the L-brackets on the two ice makers as the new one was bent. I then reinstalled the new Ice maker in the reverse order.

Repair for the most part is very easy! With the particular assembly that I purchased you MUST keep the cord, the wire piece that tells the ice maker when tray is full and the front cover from the previous part. Removal is easy. Flip wire piece up. Remove ice holder. Remove screw at bottom of assembly. Push assembly up not to hard as you don't want to break the clips attached to the fridge. Pull out far enough to disconect white cord at the fridge connection. Piece removes easily. I actually had a little ice build up in the white hose that dispenses the water. I took a cup of warm/ hot water and held up to hose to melt ice. To put back in just do it in reverse. Remove the 3 parts previously mentioned. Put on the new assembly. It was a little tricky getting the clamps to click into place. Just go slow and push upwards and towards fridge wall. This is definately worth trying yourself before calling a repair man! Good luck. Hope this helpful.

need instr. to repair

Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.

Oredered the new icemaker. They delivered fast - it was here in 2 days. One nut holds in the icemaker, then it just lifts out and unplug the wiring harness. New unit was identical, which is very nice. No modifications to make. It went right in and works perfect. Great experience.

first i flipped the power switch to the fridge and i took out the three screws unhooked the electrical, and i put the new ice maker in in the same manner hooked the electrical back up put the screws in and job was done. and about 2hrs later we had ice.

R&R unit in 5 minutes, very easy...

The swap was quite easy. All I had to do was remove 3 nuts and unplug the flat wire connector. I kept the old unit when I took it out in case I needed any parts, but the only thing I needed to transfer over was the Ice level wire. Very straightforward!

First I took the front cover of element off and pull the electric conne out. Next I loosened the two screws that hold the element top in place. I then removed the screw at bottom that fixed on L-angle.
And then took thermo sensor that was holed by cramp out.
Replace new ice making element as reverse order. It was very easy job.

remove old ice maker . replace with new

I got the replacement ice maker the next day after I ordered it...really fast shipment which was very nice. All I had to do is unscrew 4 screws, un-hook the wire harness from the back of the old ice maker and take the old ice maker out. Then repeat the same steps in reverse to put the new on in. It took less than 10 minutes if that. Very easy to install.

First I unplugged the refrigerator. Then I removed three screws holding the ice maker using a small socket set. The hardest part was unpluggung the connector on the ice maker because of the tight fit. Then I changed the plastic cover and wire rod from the old unit to the new one and reinstalled the ice maker in reverse order. l have done repairs like this before which was good because there were no instructions provided. Reading these repair stories helped remind me how easy it was to do. I had new ice in less than one hour.

Ordered Friday and received the next day. Pulled the refrigerator out, turned off the water, removed 3 screws, unplugged wire harness. Removed old harness and wire shut off rack from ice maker, installed on the new ice maker plugged in put, replaced the 3 screws, turned the water back on, finished. Took less then 10 minutes for all this to happen. Piece of cake! Had ice the next day. Never ordered, received, and fixed anything this fast!

turned off the power. took out the bottom scerw and loosened the top two screws. lifted out the old ice maker which allowed enough room to unplug the power cable from the back of the freezer. put the cables and bucket fill rod on the new unit and installed the same way it came out. turned on the power .closed the door and waited for the ice maker to cycle. it takes about 20 minutes; the ice maker has to get down to the proper temperature,