HMG191651 Admiral Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken meat drawer.
With this drawer it is a common problem in that it breaks due to the full weight of the drawer and contents being supported by just the plastic rails. The plastic rails at the top start to break and the support rails start to break as well. The repair is as simple as taking the assembly completely apart and putting the new parts in. The toughest part was taking the existing metal pull trim from the old drawer and transferring that over to the new drawer. Gently prying with a wide blade screw driver eventually did the trick to getting the old trim off. Tip: Pay close attention to where the left and right rails go before disassembling the old assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neill from Albuquerque, NM
- Parts Used:
- WP70111-108
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Retainer bar was missing.
I had to cut the bar to the right length with a hacksaw. The most difficult part was getting on the plastic supports/pins on either end. I'm not sure a hacksaw is the best way to cut a retainer bar, but it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Albuquerque, NM
- Parts Used:
- 70197-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken door shelf retainer
removed broken retainer with pliers and inserted new part. It was extremely easy---and I have ZERO mechanical skills.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bel Air, MD
- Parts Used:
- WP61004888
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
motor wore out making loud noise
unplug the refrigator, remove everything from
frezer compartment. remove ice maker three screws and un plug. remove rear panel 4 screws
remove motor bracket from rear panel 4 screws
unplug motor . replace motor and reasemble in
reverse order. the new motor is very quiet.
frezer compartment. remove ice maker three screws and un plug. remove rear panel 4 screws
remove motor bracket from rear panel 4 screws
unplug motor . replace motor and reasemble in
reverse order. the new motor is very quiet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francis from longmont, CO
- Parts Used:
- 70197-1, WP70111-108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
missing door shelf retainer
ordered new retained and fastners
cut to length per instructions
installed
repair completed
thanks for your service all parts were correct and deliver on time
wayne winkler
cut to length per instructions
installed
repair completed
thanks for your service all parts were correct and deliver on time
wayne winkler
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dahl from colora, MD
- Parts Used:
- 70197-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed retainers to keep door shelf on
placed the retains on door shelf and snapped on. the only problem I had was finding the retainers, thanks to you guys you had the parts that I needed. Plus with your web site it made my search easy. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kyle from muncie, IN
- Parts Used:
- 70197-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door shelf dudes fell off when hubby slammed door shut
I just fixed them, thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Saco, ME
- Parts Used:
- 70197-1, WP70111-108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
cut to size and installed
I simply measured for the correcy length, cut with a hacksaw, inserted the ends that attach it to the door and installed it on the door ..... simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Levittown, NY
- Parts Used:
- 66813-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Meat drawer broke
looked up the part on line - ordered it and it took my husband 10 minutes to put it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Falcon Heights, MN
- Parts Used:
- 70197-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door shelf retainer snapped in half, making the retaining bar useless.
I ordered the part online which arrived two days later. I slid the new retainer into the metal retaining bar, so that the whole piece including the prongs was inside the metal bar. Then I lined up the prongs with the holes and snapped them into place. It took about 3 minutes, and now we have our shelf back.
Was this instruction helpful to you?
Thank you for voting!