Models > JRTDX224L > Instructions

JRTDX224L (8B14B) Admiral Refrigerator - Instructions

Jump to:

All Instructions for the JRTDX224L
121 - 135 of 602
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jim from Indianapolis, IN
Parts Used:
D7824706Q, 12001414
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
water in ice bin
replaced the water valve - just precautionary with unit age.
Problem was ice tray coating was breaking down causing ice to stick during harvest cycle - refill would cause water to overflow to bin.

Removed bottom screw, loosen 2 top screws, lift ice maker up and lay over to expose wiring harness, unplugged, then reversed installation
Make sure fill tube in back of ice machine is positioned in fill trough

Recommend that on any installation use a commercial grade water filter system and change filters annually, this is the first repair because of that- unit is 18 years old

commercial refrigeration guy
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Randy from Yale, OK
Parts Used:
4318047
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
ice maker quit working
Replaced the water valve. I knew that the ice maker was working by watching the movement. It was not getting water to it, s I figured it was the electric water valve and sure enough, that fixed the problem.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Charleston, SC
Parts Used:
D7824706Q
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Quit making ice
Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Linda from Richmond, VA
Parts Used:
WP61003336
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Ice Maker couldn't drop ice through the door.
I pulled the drive ring off of the icemaker and replaced it with the new part. Saved a $150 service call plus cost of part. It cost me a little over $11.00 and a repairman probably would have charged $30.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Granada Hills, CA
Parts Used:
833697
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
refrigerator was overheating, condensor fan dead.
First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Bloomfield Hills, MI
Parts Used:
4318047
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
Old Valve was dead
This was very easy and pretty fast to do and its working great...all for $40 bucks ! you can do this...trust me!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from Berkeley, CA
Parts Used:
WP628356
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Ice maker broken. Quick fix
The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Lowell, MI
Parts Used:
833697
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Socket set
original motor stopped
removed old and instaslled new. biggest problem was getting to one of the screws.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roberta A from WINTER HAVEN, FL
Parts Used:
D7824706Q
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
icicles from pooled water in ice collector bucket
I watched the repair video on the web site a couple of times just to get comfortable with what to expect. (i.e. pressing tabs on wiring harness to remove, placement of lift arm for removal and installation) These instructions were a big help...I had the removal, modifications and installation completed in less than 30 minutes. Ice cubes (without the extra icicles) in 1 hour...
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from WALWORTH, NY
Parts Used:
WP61003336
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The ring was cracked and it would not dispence ice.
I switched the ring and still had the same problem. What caused the Drive ring to crack was the Ice maker drive was cracked also, when it filled with water it would tip. The ice was not freezing completely and would cause the ice to build up and the auger was froze with ice or a big piece of ice would jam it. So I replaced the Ice Tray, it is working like new. I have to buy another ice tray as inventory, although I know inventory is bad but I never agreed with that theory.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeannine from Pontiac, IL
Parts Used:
D7824706Q
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Ice Maker leaking.
I watched the video regarding the instillation of this ice maker a few times and then followed it exactly. It was incredibly easy. We had ice cubes about two hours later and no longer had a leak making icebergs!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
GREGG from WEST CHESTER, PA
Parts Used:
4318047
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Ice maker was not working.
Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice maker. Gregg in PA.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from SAN DIEGO, CA
Parts Used:
D7824706Q
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Ice tray was corroded and leaking
Removed top drawer from freezer. Unplugged the ice maker. Uncrewed the bottom screw. Loosened the two top screws. Removed old ice maker. Removed all the parts that didn't come with the new ice maker and installed on new ice maker. Reinstalled the new ice maker. Started making ice with no leaks in about 3 hours.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindy from BEN WHEELER, TX
Parts Used:
12001773
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Ice Maker would not dispense ice
Had to cut the old part off with dremel then just install new part and put back in refrigerator. It is a good thing to know that the Yoke is a left threaded. Thanks James from Pineville.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dan from LAVISTA, NE
Parts Used:
D7824706Q
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Replace Ice Maker
I have a Maytag Refridgerator with lower freezer and ice maker. Stopped making ice. Noticed the unit would fill up and freeze but the tray wouldn't rotate to drop the cubes into the tray. Cleared the frozen trays to see if it was just stuck but same thing happened. Replaced unit, not difficult with the exception that the top tray is ridiculously hard to get out. Never did do it, just worked around it. Working perfect now.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JRTDX224L
121 - 135 of 602