LTF2112ARZ Admiral Refrigerator - Instructions

The video of the installation was the best help I have ever had. Rather that vague written instructions that are usually so poorly written they are of no help, the video showed exactly how to do it. I wish everyone provided videos like this!

Remove bottom screw loosen 2 top screws unplug connector from back of icebox. Lift up and pull forward. Swap front cover full bucket stop bar and wire (plugs in) reinstall 10 minute job

the diagnosis was the most difficult step.. and trusting that the one visible nut was the only thing holding it on.. (there are 2 other clips that you need to use a little force on to detach). remove the ice maker (one nut, 2 clips, detach plug).. then remove the 3 screws holding on the 'face' , pry face off, you will see where the 'contact' has burned/melted/worn away. replace unit. 80% of the time, this is the problem (according to my research)

Model#MBF2255KEW (bottom Freezer) Turn fridge and freezer controls OFF. Move fridge out away from wall to give yourself working space and to clean later. Disconnect electrical plug from wall. Turn off water supply at wall or floor. Put down towel to catch excess water and disconnect water hose at water supply, lay it on towel. Move to the inside of freezer and remove freezer bins by pulling the door all the way out as far as it will go and then lifting by the handle up. locate the two hooks in the back and push forward to clear the bar and move to a safe location. Push the two rails all the way back into the freezer. Un plug wire harness from freezer by squeezing both side of the plug at same time and pull off. Remove the 3- 1/4" nut screws (2 at top and 1 at bottom ) from the ice maker and remove. Take the front cover, Wiring harness and wire bail from old ice maker and place it on the new ice maker. Install new ice maker and connect the wiring harness plug to the freezer connection. Hook up water line hose and tighten. Turn water on and check for leaks. Plug fridge into wall outlet and set refrigerator and freezer controls to 3 until refrigerator is cold and then set as needed. Give the ice maker from 3 to 6 hours to freeze and wait for that magical sound of ice being dumped into the bin. Throw away first batch of ice to make sure there are no impurities. Check for the delivery date of the new ice maker before you start and have coolers and ice for perishables. I removed the old one on the delivery date and cleaned the fridge and freezer inside out. I came to this page to get my repair plan and I hope this will help someone else.

Removed old ice maker, had to use the wire shutoff from old ice maker installed new one. Very easy repair, very nice product cheapest price on internet.

Removed the elec connection (after unplugging app) found it easier to remove from appliance. Remove the three screws ( do not temove,....just loosen, the top two) bottom must be removed! Insert the power connection, exchange the tilt up rod, line up the water connection and place back on the two top screws. Tighten and relpace the bottom screw. I found out the hard way.... you cant't see the two top screws . The slots on the ice maker just fit over the screw heads.... it's cold in there!!!

Hopoe this helps..

Cape Cod

Arrived soon than expected. Unplugged some wires, removed face plate, 3 screws--install and do reverse.

Easier than I would think---Saved $150- to have someone else do it.

Works fine.

I took the screws out holding old old ice maker, unpluged the electrical socket and old unit came right out. All I had to do then was plug electrical socket into new icemaker place unit in position and put the one screw back in the held it in place. Plug frig and and it filled with water in about 15 minutes and started making ice. Part was a exact match to the one I removed.

It was real easy. I unpluged the fridge. Took out the three screws that held the icemaker to the wall. Unpluged the wire harness. Removed the old icemaker and reversed the order to install the new one. Everything lined up perfectly.

Removed one screw ,unpluged ice maker, and replced it with new one.

very simple,remove old and unplug install new,three screws, used old hose clip.

First i removed the top two screws that help the ice maker in place then remove the bottom screw, then unplug unit from freezer, removed ice maker for freezer, took out wire harnes, put wire harnes in new ice maker, plug new unit in place the unit in freezer and put in the bottom screw, them align the top two screw and but them in and was done. Check ice maker in two hours and there was new ice being made.

I removed the fan cover and pulled out the fan that had the broken piece and replaced it with the new parts. Very easily done. This simple procedure would have cost over 75 to 100 dollars. I did it with less than 50

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

Followed the other directions -- I have the bottom tray freezer. It was really easy to unscrew the screws -- a bit of a reach to get them all, but not a problem. Leave the top screws half-way in and it's a bit easier (the icemaker has the brackets that just sit on the screws). Thanks to everyone who left instructions!