HMG22494-7A Admiral Refrigerator - Instructions

I removed all covers then removed screws from element and disconnected wires and removed it.
when installing the new heater I payed close attention to the routing of thw wires to insure that the terminals were connected properly. I then replaced all covers and turned the frig on and in a couple of hour it was working great again

I removed the old icemaker, took it out to my shop & removed the wiring and etc. and put it back in place.

very easy, 3 screws,took old one out, take 2 inter screws out (of ice maker) of old unit to replace water feed cup on new unit very easy,installed had ice after 12 hrs.

I simply removed the 3 screws holding the unit into the freezer with a nutdriver, then disconnected the power plug (a little hard to get to, and requires releasing a small tab in a hole in the main body). The icemaker came right out with no problem. I then had to change out the water funnel inlet because mine had a different style than the one provided on the new one. This was easy also, just remove 2 phillips head screws that are set deep in 2 holes in the face of the motor drive unit, then pull the whole assembly apart far enough to allow the ejector blades to slip out of the hole through the inlet funnel, then snap the funnel loose to move it to the new one (the same technique to be used on the new one, then re-assemble in reverse order).

I first loosened the hex screws and lifted the unit off. Then I unplugged old unit from the wiring harness. I did have to switch the inlet funnel since the new unit was a little different. I used the one from the old unit. I then plugged it back in, rehung and tightened the screws. The unit started operating within a few hours.

First i removed the three screws that held the assembly to the fridge, then removed the water flow tube from ice maker. 2- flipped ice maker over ,then used a small flathead to push in locking tab that held wire harness and out comes ice maker. All though the water cup was not quite the same i used the old ice maker to take apart to see how it was put together,hopeing there wasn't a myriad of parts. -NO INSTRUCTIONS- piece of cake, don't take out outside screws,take out the 2 inside screws-these srcews hold the guts to the water tray-pull apart and reassemble the unit after you have switched the cups. then reinstall into fridge with your outside cover and the full bin wire and your done. It helps to be alittle mechanicly inclined. -NO GUTS NO GLORY,DONT BE AFFRAID TO LOOK OUTSIDE THE BOX-

First, unplug power to Fridge, then remove ice bin and set to one side, then remove the clip that holds the fill tube down by pulling up on it, and remove the fill tube. Remove the two top screws on ice maker assembly first, as the bottom screw will support unit. Then remove the single bottom screw. Rotate the Ice Maker slightly down and this will expose the electrical connector. With a short, small, flat head screwdriver in your left hand, depress the locking tab for the connector, while your right hand supports the assembly and pulls the connector outward to disconnect. Remove old Ice Maker, and remove the bin full lift wire, it's a slide in fit and install in your new unit. Check your fill tube water diverter on the right side of Ice Maker unit , you may need to remove the blank, it is U shaped and molded for easy removal, but use caution when removing to be on the safe side, this allows the fill tube to go down into the diverter, Re-Assemble in reverse order. Give the unit plenty of time to reach proper operating temp, and cycle. Make sure and discard your first Ice cycle.

Unplug the Frig and left the freezer side total defrost. Mine was so frozen up, it took about 6 hours with the door open. I had a towel in the botton to catch all the water and ice that fell.

Removed all the shelving units. There are 3 screws that hold the ice maker in place. Loosen the 2 screws above the ice maker about 3 or so turns. Then remove the screw under the ice maker completely. Then lift the ice maker off of the 2 screws that you just loosened. Then with a small flat blade screwdriver, push the plastic clip that holds the connector of wires that plug into the ice maker.

Then remove the screws that hold the back plastic cover that conseals the coil.

Now you should see the coils. There is one heater unit in the middle and one at the botton. There is a screw on each side of the heater unit that you need to take out. They are screwed into a metal bracket that is part of the coil system. Once the screws are removed, you simply remove the heater units. They are plugged in at the top of the coil system on a circuit board. Unplug them from there, (one of the spades connector was slightly bigger then the other, so I new where to plug them back in). Fish all the wire and heater untis out and you are ready to re-oinstall the new units.

Getting the wires back up through the coils was tricky, but I was able to do it.

The hardest thing was working inside the freezer unit. It is not very wide and was sometimes hard to get both hand inside to work.

Most of the stories on repairing this ice maker indicated that was real easy until describing the Amana version. The fill tube attaches differently. The recommendation was to use your old "cup". I have found that to make the change required that you find a philips screw driver and locate two access holes in the motor end of the control unit. you can loosen those two screws (they won't fall out) all of the way and pull the control unit from the tray part of the ice maker. DON'T remove the three screws that hold the control unit together or rotate the sprocket. This will allow you to disassemble the parts that hold the "cup" in place. Just remember "if it isn't coming apart easily your not doing it right".

First I loosened 2 phillips head screws at the top of the ice maker (the one that is close to the front is a little difficult to get a screwdriver on). These 2 screws do not have to be removed. Took 1 screw out of the L-bracket at the bottom of the ice maker. I then slipped the icemaker upward from the 2 top screws and unplugged the electrical wires at the connector at back of the refrigerator to remove the ice maker. I then removed the front cover from it and placed it on the replacement ice maker. I also swapped the L-brackets on the two ice makers as the new one was bent. I then reinstalled the new Ice maker in the reverse order.

I simply removed 3 nut head screews and the old unit came off. I removed the ice level arm off the old unit and put on the new one. I removed the old wire harness and plugged into the new unit. I mounted the new unit, plugged it in and was done. I had ice in less than an hour. So simple my 11 year old could have done it without help.

first removed bottom screw. then loosened two top screws enough to lift and free icemaker. held unit out slightly from wall of fridge and unnplugged wiring plug, freeing icemaker. then took wiring harness and wire bail from old unit and installed on new icemaker. then plugged new unit in and attached to fridge. in about 30 minutes it started making ice. Has worked well since.

disconnected wiring from ice maker to refer.
removed three mounting screws holding the ice maker to the refer. removed ice maker, removed the wiring from old ice maker and installed on the new one. installed new unit making sure that the water filler tube is in the correct location. plug the wire back to the refer. Done

Remove ice bin. Loosen two mounting screws holding ice maker in place ( not necessary to remove screws), Remove two screws holding cover over ice auger. Behind cover is connection for ice maker. Need two hands to disconnect wiring connector from ice maker( tight area to work in,narrow shoulders and long arms help). Squeeze tab on one end of connector while pulling connectors apart. DO NOT PULL ON WIRES, ONLY PULL APART CONNECTORS.
After ice maker is out use pin points on end of timer to check contact points to be sure all contacts are made. Is possible to insert an Ohm meter probe in holes at end of timer, it is not necessary to remove timer to check unless problem is found with open contact.

Removed one screw that held the unit in place. Took a few minutes to determine how to disengage the unit from the plastic clips. The most difficult part was disconnecting the electrical cable.but in less than 30 minutes the new unit was in place and filled with water to start forming ice.