GS395LEGB0 Whirlpool Range - Instructions

the research and diagnosis took much longer than the repair on this model. if i had the new igniter on hand, it would have been only about 15 mins.

pulled the stove out removed back cover, unplug then unscrew igniter. Mounted new igniter in place, plug it back in , put cover back on, put stove back in place. Took about 20 min. Very easy repair, thank you.

We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.

Turn gas off at tank. Oven rack out. 2 screws out of flame spreader and remove. 2screws from ignitor. Pull oven out from location to access rear bottom cover. 2 screws out and unplug ignitor. Guess what ? Reverse order. Not worth paying gas company over 250 dollars.

I just removed the bottom panel in oven and the igniter was right where the flames should be and I removed the two screws and replaced with new part. I replaced bottom oven panel. You need to remove rear panel and plug wire and replace rear panel. My problem was solve. It took 20-30 minutes tops.

The brief comments on how to with the order was most helpful, no problems replacing frame. Quality is good I thought the price was very high for the parts, considering plastic and metal pieces, but then again compared to new stove reasonable. Remove pieces replace back in order removed.

Put the bottom of the glass in first then put the top half into the brackets in the door handle. Holding it in place with your extra set of hands tighten it down with the two screws from inside the oven door into the back of the handle. The door will be open a lot so be extra careful not to let the door close onto your hands or fingers. Also remember patience is a virtue.

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

So....the oven stopped working.
I called a local appliance guy and set up an appointment to repair.
$90 to travel here.
$50 for the part
$ labor was about $75
..then tax.
BUT then....I had a moment of clarity.
A new Oven/Range/Stove top was about $400.
This guy was over $200 to repair a 4-7 yr old stove.
So I ordered the part.
A resus monkey could have fixed the stove...I really mean it...Easy is an under-statement.
I found a tutorial on you tube (how to change an Igniter.
Literally 6 screws and unplug the igniter and install the new igniter.
Replace the screws and replug in the unit.

and that's that.

Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.

Remove old grate place new grate on gas stove top

Unplug the electrical cord. Remove all the grates and burner caps. Remove the two philips-head screws on each burner. Slide the plastic putty knife under the cooktop in the front to locate two clips. Push in to disengage clips and lift cooktop up in front. Disengage cooktop from the rear of the range. Remove the bad igniter from the burner head and replace with the new, Disconnect the wire from the spark module and install the new wire. Replace the cooktop by securing the rear first and then lowering into place until the clips engage. Replace the philips screws on the burners and the caps and grates. Plug the range back in and you are done.

Remove the side covers. Remove the 2 screws on the back side of the door, hold on to the glass and front panel, they will fall out. remove the 2 screws holding the handle. Put the new handle in place and insert screws, note the old handle had metal inserts that are threaded, the new does not. Had to push very hard and let the screws bite into the plastic.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I took apart the bottom of the oven to see the ignighter. I moved the oven away from the wall and took off the metal plate that covers the ignighter electrical connection.Unplug the old part and plug in the new one. With the nutdriver remove the two screws holding the part onto the gas tube. Save the screws and attach the new part with them. Turn on the oven to see if the gas tube lights. If all is good put the metal plate on the back of the oven and replace the other oven parts. Make biscuits!!