SF357PEKQ0 Whirlpool Range - Instructions

removed the old ones.then installed the new ones.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Screwed in light bulb and glass protector

my son simply replaced the switch, so now I have a working oven light once again

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Ordered the replacement part., removed the old trim from the door and reinstalled the new trim. On the drawer glide, I simply reattached a new one to replace the one missing.

This repair is only if your old igniters are working but they are so cracked that the spark is not going where it should be. TURN OF THE GAS SUPPLY VALVE BEHIND THE STOVE AND UNPLUG THE STOVE FROM THE WALL.I had to drill out most of the old screws to remove the burners plates because of all the old baked on spills. I bought replacement screws when I bought the igniters because I felt this would be a problem. My repair time included scrubbing the stove top. Once all the parts that make up the stovetop burners were removed (NOTE WHICH BURNER PLATE CAME FROM WHICH LOCATION, THEY ARE DIFFERENT SIZES) and I could see the pipes beneath the stove top, I cleared off the top and used a spreading knife to push in the clips on the left and right sides near the front of the stove. It was thin enough to fit in the space between the stove top and main body. Push the clip inward and pull up on the stove top and it will let you lift the top. Be careful because it may release suddenly so be gentle. I also removed the top section of the back of the stove to access the igniter terminal block. A few screws, nothing more. Be sure to take note of which wire goes where. (They are color coded). Unplug the old igniters. it is easiest to cut he old igniters off of the end of the wires and pull out three wires leaving only one. At the back left of the top of the stove there is a rectangle channel that the wires are running through. There is a clip that holds the wires loosely together. Remove the wires from that clip or the next part will be difficult. Run each of the new igniter wires through their respective holes in the stove top. BE CAREFUL NOT TO DAMAGE THE WIRE INSULATION IN ANY WAY. When you put the burner plates back on the igniters will be sandwiched in between the plate and the stove top. Using electrical tape, tape the connector ends of the new wires to the one remaining old wire. Gently pull the old wire through the rectangle channel, pulling from the back of the stove. Take your time so no damage occurs. Once the wires are pulled, plug them in to their respective terminals and place the wires in the loose clip. Make sure the new wires are not crossing the pipe openings where the burners are located. You can close the stove top and double check there are no wires across any of the burner openings. Re-assemble the burners and plug in the stove. DO NOT OPEN THE GAS VALVE. Turn on the stove and check to make sure the new igniters are working properly and sparking to the burner plate assemblies. You should see a controlled spark. Do not touch the burner plates or igniters or you will be shocked. If all are working then you may put the back cover on and open the gas valve. If none are working make sure the stove is plugged in. If some are working then check the connection on the terminal block and the wire insulation. If they are still not working then you've got bigger fish to fry. Good luck my friend. Happy fixing!

Excellent delivery.

Lifted the top disconnected the old valve and replaced with a new one.I believe the valve should have been shipped with two gaskets,. One for the bottom and another for the top. I reused the old one on the top with no problem but would have preferred a new one.

Turn off the breaker to the range. Unplug, too. Took off the 8 screws that hold the upper back panel on. Took a picture of the wire setup (this ain't my first rodeo). Removed two screws on the bottom of the old latch that hold it in place. Carefully removed the wire leads with needle-nose pliers because I didn't want to replace the wire leads. Reconnected the wires to the new latch, replaced the two screws to hold it onto the oven. Tested with the rocker switch on top and the oven door, both worked. Put the back panel on with the 8 screws.

Remove old knob and put new knob in. About 10 minutes total.

Remove oven racks. Remove bottom of oven. Mine was held in place by two large screws in the back part of the oven. They did not screw into anything. Lift out bottom from the rear. Remove burner cover plate by lifting the front and pulling out. Mine was not screwed in. The igniter is mounted on the burner and held by two 5/16 small bolts. The top one is easily accessible. The bottom is a real witch. You need 1/4inch socket set with universal connector to remove. There is a single wire attached to igniter by a wire clip. The wire is accessible by removing the bottom pan storage drawer under the oven door. Unclip the old attach the new. Screw two small bolts back in and replace things you took out. TURN GAS AND ELECTRICITY OFF BEFORE YOU BEGIN. Parts select should allow the igniter to be sold separately rather than connected to the burner. I only replaced the igniter. Replacing the burner would be a real chore.

This could not have been any easier. The site walked me through selecting the correct part and it arrived quickly. When I got the part, it slid right on.