RDE1300P2 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kay from Cottage Grove, MN
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element burned out and cracked
Removed two screws, removed two clips, removed the element and rehooked the two clips and screwed the two clips back in. Zip Zip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Quinlan, TX
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element burned up
unscrewed two screws, unpluged two wires, put screws back. turn off power!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Paoli, OK
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom heating element in our oven stopped heating
Unscrewed two small screws and took the old element out, and installed new element. It took less than ten minutes to repair. The new element works beautifully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Granite Falls, NC
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
My heating element had been melted through by some type of food and was severed into 2 metal peices. It could no longer be used without dangerous consequences.
I got my part in the mail and FIRSTLY, unplugged the entire stove from the wall. I unscrewed the old part from the front, took the panels off the back, and disconnected the element from the yellow and red wires.I removed the old part completely from the stove. I then put the new part in, reconnected the wires, screwed the part into the oven, then BEFORE putting the back paneling on, I tested it. The new element works like a dream. I then, put the paneling back on & was finished!
BE SURE WHEN YOU BUY TO CHECK WATTAGE OF YOUR OVEN TO YOUR ELEMENT. Voltage doesn't matter because most voltage is the same in any house you live in...
BE SURE WHEN YOU BUY TO CHECK WATTAGE OF YOUR OVEN TO YOUR ELEMENT. Voltage doesn't matter because most voltage is the same in any house you live in...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W Pendleton from Cumming, GA
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
After 12 years the element died for the 2nd time We thought about getting a new oven, but ours has become sort of "retro" looking. I think it's from the '60s. We looked on line and found the part at a reasonable price and decided to give it a try.
I first went to the breaker box and shut off the power to the oven.
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from HARRISBURG, IL
- Parts Used:
- 326791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake Element
Piece of cake. Removed door and racks, screwdriver to remove element. Reversed operation and back in service in no time. Good as new. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Vassar, KS
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven quit heating
My daughter told me here oven had quit and ask my advice. I saw where the element was burnt. Took out 2 screws unkooked the wires. I was unable to get help at the local Appl repair store so I went to internet to parts select.com I put in model # and had the part within 3 days put it back in and worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Indiantown, FL
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element melted through
Unscrewed the two screws holding the rear plate of the element. Pulled the element out far emough to reach the plugs on each side. Disconnected the plugs and plugged in the new element. Put the screws back in and it was ready to go. This was the second replacement in the last five years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Lake Quivira, KS
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lower heat element burnt out
remove two screws at rear of heat element unit. gently pull element to expose wires connected to heat unit. pull connectors apart on each end (don't let wire slip back into wall hole). connect new unit to wires, insert back into holes and replace screws into back wall of oven. Done... Now that I have done it once, it would now take less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from West Ossipee, NH
- Parts Used:
- 326791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lightning cooked the element
turn off the oven breaker - unscrew both sides of element, pull through holes & remove wire ends. Replace with new element, reversing procedure - turn on breaker & you're good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Mankato, MN
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Baking Burner Went Out
Turned off power to unit onswitch box. Used Phillips screwdriver to take out old unit.Could come out at least 3"with connecting wires with clips on their ends. Disconnected clips ,connected clips to new unit and put back in place. Redid screws. Turned on power.... Wa-La ... Works Great. Thank You Very Much for your service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from SIOUX FALLS, SD
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element didn't heat
Easy as 1, 2, 3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DEBRA from TOOL, TX
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat, but broiler did work. Heating element needed replacing.
The part arrived in less than 2 days. I turned off the main electrical switch to the house. All that had to be done was remove two connecting screws in the back of the oven holding the heating element in place. Then I removed two connecting wires with needle nosed plies. I reversed the process with the new element, turned the power back on, and the element heated up and back in business. This was the easiest I have ever had repairing or replacing anything. The hardest part of this repair was finding a flashlight in my house that had good batteries!! Thank you for such quick and courteous service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Sheboygan, WI
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower element had shorted out
we replaced with the appropriate part from Part Select. The agent on the phone was extremely helpful with finding a part for our old oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Fort Lauderdale, FL
- Parts Used:
- 326791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned Out Baking Element
Simple to unscrew the 2 screws holding the element to the back of the oven. Unclip the wires.
Was this instruction helpful to you?
Thank you for voting!