SF362BEGN1 Whirlpool Range - Instructions

simple change out - remove old grates, install new ones - note that this site/store is excellent

Removed two screws and the front of the door popped off. Replaced the bottom metal piece that the glass front slides into. It was a piece of cake.

removed door handle screws then removed glass retaining tabs from sides put clips on sides of glass held insuation in place and replaced glass replaced door handle replaced two door screws trial opened and closed door successful done

Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

First I removed the two screws that hold the glass cook top in place. Then I removed 4 screws that hold a small metal plate that shields the switch. Replacing the switch was very simply just a matter of unplugging four wire connectors from the old switch, sliding the new one in and reconnecting the wires. It was very easy to find the part on the website. I just located the switch on the diagram and ordered the part. I really surprised my husband that I ordered the part and repaired the stove by myself. He was intending on calling a repairman, but I did it myself.

Replaced bottom trim included in kit.
Installed side door trim.
While trying to slide glass front in place both plastic side trims broke.
Had to use already broken door trim and glued in. Just hope when use oven glue doesn’t melt and will have to replace entire oven.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

Removed bottom pan from oven, removed gas flame deflector to expose ignitor and burner. Saw that ignitor was not working. Removed two mounting screws, pulled ignitor and wire until wire nuts were exposed and disconnected ignitor. Replaced with new ignitor, bracket and wire nuts. Remounted the new ignitor, and tested burner. Worked ok. Reinstalled deflector and pan, back in business.

REMOVE BACK COVER. UN PLUG, REMOVE TWO SCREWS IN SIDE OVEN, PULL OUT , REPLACE, REATTACH, FIXED CODE F-3

This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.

Simply removed the bottom drawer, unscrew the old broken glide, and attach the new glide. Simple and no hassles.

I read some of question & answer to the problem I was having with the oven. When I saw do-it-yourself that all I need to know. Repair man quote me for 100.00 dollar he will do it plus part. So I save 100.00 dollar and done it myself. Thank to partselect for fast and quick delivery service. It was only 2 screws holding the element and the connector was a just plug it into the other plug very easy to do. I will always come back partselect for answer and help and buy the part from them. YOU ROCK PARTSELECT

new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!