SF315PEGQ5 Whirlpool Range - Instructions

First time was very difficult I tried to make the panel fit into the frame. Broke both side pieces of the trim.Even thouth I broke the trim PartSelect replaced them. I did not expect that.Second time it was easy. Remove the handle first and then the panel slides into the top and bottom only. It does not slide into the side of the frame but sits on top of it. Thanks, Allen

We ordered our part from PartSelect.com, of course, using their diagnostic tool(s). We received it very rapidly after ordering (a day or two). It involved taking two screws out of the bottom plate of the oven. There were two screws in the diverter (?), but they weren't attached to anything. I had my son, who is young, strong, and small get behind the oven to locate where the igniter plugged in. He detached it and I unscrewed the nuts holding it in place. One of them was in pretty crooked and made it a little difficult. But I pulled it out. I put the new one in place, my son plugged it in, and I replaced the two nuts, securing the new one in place. I replaced all the parts and their screws while the wife cleaned the gunk from behind where the stove sits. We did perform a quick test prior to re-assembly and it looked good. Re-attached everything, put it back in place and it's working like a dream. Just in time for Fall baked goods...

The igniter would glow but no gas was released to the burner. I was told that the igniter is bad because it is not getting hot enough to open the safety valve to release the gas to the burner. I turn the gas off and unplugged the oven. Opened the oven removed the racks then removed the two screws that hold the bottom plate of the oven. Now I can see the burner and the igniter. The igniter is held on to the burner with two screws. Unscrew then and unplugged the wires. Then replaced with new igniter. Replaced everything that I removed. Plugged oven back in and turned on gas. Then started oven, it takes 45 sec. for the igniter to get hot enough to release the gas and everything was working.

Remember how you remove the glass. The side brackets go under the glass.

Removed a cover plate on the back of the stove. Unplugged the old igniter. Pulled the bottom drawer out. Reached in under the stove and undid the 2 screws holding the igniter in place. Screwed the new igniter in and put everything back together. The only tricky bit was reaching the igniter through the bottom drawer opening.

This repair is only if your old igniters are working but they are so cracked that the spark is not going where it should be. TURN OF THE GAS SUPPLY VALVE BEHIND THE STOVE AND UNPLUG THE STOVE FROM THE WALL.I had to drill out most of the old screws to remove the burners plates because of all the old baked on spills. I bought replacement screws when I bought the igniters because I felt this would be a problem. My repair time included scrubbing the stove top. Once all the parts that make up the stovetop burners were removed (NOTE WHICH BURNER PLATE CAME FROM WHICH LOCATION, THEY ARE DIFFERENT SIZES) and I could see the pipes beneath the stove top, I cleared off the top and used a spreading knife to push in the clips on the left and right sides near the front of the stove. It was thin enough to fit in the space between the stove top and main body. Push the clip inward and pull up on the stove top and it will let you lift the top. Be careful because it may release suddenly so be gentle. I also removed the top section of the back of the stove to access the igniter terminal block. A few screws, nothing more. Be sure to take note of which wire goes where. (They are color coded). Unplug the old igniters. it is easiest to cut he old igniters off of the end of the wires and pull out three wires leaving only one. At the back left of the top of the stove there is a rectangle channel that the wires are running through. There is a clip that holds the wires loosely together. Remove the wires from that clip or the next part will be difficult. Run each of the new igniter wires through their respective holes in the stove top. BE CAREFUL NOT TO DAMAGE THE WIRE INSULATION IN ANY WAY. When you put the burner plates back on the igniters will be sandwiched in between the plate and the stove top. Using electrical tape, tape the connector ends of the new wires to the one remaining old wire. Gently pull the old wire through the rectangle channel, pulling from the back of the stove. Take your time so no damage occurs. Once the wires are pulled, plug them in to their respective terminals and place the wires in the loose clip. Make sure the new wires are not crossing the pipe openings where the burners are located. You can close the stove top and double check there are no wires across any of the burner openings. Re-assemble the burners and plug in the stove. DO NOT OPEN THE GAS VALVE. Turn on the stove and check to make sure the new igniters are working properly and sparking to the burner plate assemblies. You should see a controlled spark. Do not touch the burner plates or igniters or you will be shocked. If all are working then you may put the back cover on and open the gas valve. If none are working make sure the stove is plugged in. If some are working then check the connection on the terminal block and the wire insulation. If they are still not working then you've got bigger fish to fry. Good luck my friend. Happy fixing!

Opened lower door of stove located ignitor removed 2 small screws that secure part, took guard off back of stove unplugged wire connector removed part plugged new ignitor in re-installed guard, re-installed 2 screws that secure ignitor. Turned stove on oven lit problem solved. This is the 3rd time i have used instant repairman on parts select to fix 3 different applicances and have saved hundreds of dollars fixing it myself with the help of parts select.

Removed bottom plate by pulling up from the back (had some resitance), Two machine screws holding cover over igniter, used 3/8" socket to remove. Pulled oven from wall to disconnect igniter @ coupler, unscrew one more machine screw, fed replacement igniter into slot and coupled, attached single screw to pipe, put cover w/ 2 machine screws on top, install bottom plate. Had to use butter knife to get bottom plate to fit into the front cabinet area of stove. Done & working fine.

I removed the oven racks, removed the oven floor and the oven burner cover, pulled the range out and removed the small panel on the back which covers the igniter connector. I disconnected the old igniter, removed the two screws holding the igniter in place and removed the old igniter from the oven. Then screwed on the new igniter, fed the wire through to the back and connected the new igniter. Turned on the oven and voila' we have ingnition! The oven is working again but I'm getting the "F2" routine sometimes. It doesn't do it every time but when it does I unplug and replug and then it works. I'm a 67 year old female and I considered it very easy so pretty much anyone should be able to do this repair.

I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!

most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem

The kit was not supposed to fit my particular model but I felt the picture was exact and took a chance and had it sent. It was a perfect fit and was easy to assemble and looks like a new stove. I paid one third of the cost estimates that I got from local appliance centers and even other on line sites. I'm very please with the product and the delivery was more than prompt!! I couldn't believe the service!!! Thanks!!

Since the broiler worked fine, I took the igniter from the broiler (exact same) and moved it to the bottom and sure enough oven ignited fine. I did this to isolate the problem, because it could have been either the igniter or the valve. I put the broiler igniter back on top when I got the new part, because it is used only 5% of the time. Be aware that you may need to rummage for some machine screws because the factory screws stripped when I removed them. The oven must have annealed them.

Really quite simple. Remove the racks - remove the two screws in the back of the bottom plate - slide out. remove the bottom drawer. remove the two screws holding the igniter - unplug the old igniter and remove. screw in new igniter, plug up new igniter, replace bottom drawer, replace bottom pate, replace racks. I did turn off the gas and electricity to the unit before repairing - and it was easier for me to get behind the unit to unplug/plug the igniter. works great! thanks!

This could not have been any easier. The site walked me through selecting the correct part and it arrived quickly. When I got the part, it slid right on.