YWGE745C0FS0 Whirlpool Range - Instructions

Repair has not been made yet still waiting for the part. The part is on order and was told it would be shipped in 1/3 business days. Still waiting for the part to come from China. This is the problem with parts being made out side the U. S. A.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Took the old levelling leg out and screw the new one in.

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

I watched the video you provide and it answered all my questions. You estimate repair at 10 minutes. My wife said I waz done in under 10 minutes Watch the video, it explained every step and all the little tricks to the snap connections.

Looked up the part in the online manual, watched a YouTube video, removed upper back of range, swapped out part. Saved $200!!

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

Removed old racks, installed new racks. Recycled old racks.

I followed the instructions as provided. When I finished I noticed the switch was 1/4 turn out from the off position mark on the stove. So I pulled the stove back out and took the back panel off again pulled the knobs back off took out the screws that held the switches in place and rotated the switch 1/4 turn counter clockwise. Then I replaced all the screws and knobs . Then I replaced the panel and shoved the stove back in place. One of the burners was an eight inch and the switch doesn't work as well as it could. However there was not a direct replacement for the eight inch burner.

Ordered new element from PartSelect. It arrived shortly. It did not match the original. Guy at appliance store explained how I could connect the wires on the new one. It still did not fix the problem. A repair man tried for 2.5 hours to fix it with no success. Now I will return the replacement element in the return envelope provided.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564